DuraComm PSRM-1248NFPMU Owner'S Manual Download Page 20

Duracomm | 20 

Section 5 | Warranty 

DuraComm warrants to the initial end user, each power supply manufactured by DuraComm to be free from defects in 
material and workmanship when in normal use and service for a period of three years from the date of purchase from an 
authorized DuraComm dealer. 

Should a product manufactured by DuraComm fail or malfunction due to manufacturing defect, or faulty component, 
DuraComm, at its option, will repair or replace the faulty product or parts thereof, which, after examination by DuraComm, 
prove to be defective or not operational according to specifications in effect at the time of sale to the initial end user. The 
product that is replaced or repaired under the provisions of this warranty will be warranted for the remainder of the original 
warranty period, only, and will not extend into a new three-year warranty period. 

The limited warranty does not extend to any DuraComm product which has been subject to misuse, accidental damage, 
neglect, incorrect wiring not associated with the manufacturer, improper charging voltages, or any product which has had 
the serial number removed, altered, defaced, or changed in any way. 

DuraComm reserves the right to change, alter, or improve the specifications of its products at any time, and by so doing, 
incurs  no obligation to install or retrofit any such changes or improvements in or on products manufactured prior to 
inclusion of such changes. 

DuraComm requires any product needing in or out of warranty service to be returned to DuraComm. All requests for 
warranty service must be accompanied by proof of purchase, such as a bill of sale with purchase date identified. DuraComm 
is not responsible for any expenses or payments incurred for the removal of the product from its place of use, transportation 
or shipping expenses to the place of repair, or return expenses of a repaired or replacement product to its place of use. 

The implied warranties that the law imposes on the sale of this product are expressly LIMITED, in duration, to the three (3) 
year time period specified herein. DuraComm will not be liable for damages, consequential or otherwise, resulting from 
the use and operation of this product, or from the breach of this LIMITED WARRANTY. 

Some states do not allow limitations on the duration of the implied warranty or exclusions or limitations of incidental or 
consequential damages, so said limitations or exclusions may not apply to you. This warranty gives you specific legal rights 
which vary from state to state. 

This warranty is given in lieu of all other warranties, whether expressed, implied, or by law. All other warranties, including 
WITHOUT LIMITATION, warranties of merchantability and fitness or suitability for a particular purpose, are specifically 
excluded. DuraComm reserves the right to change or modify its warranty and service programs without prior notice. 

Section 6 | Contact Us 

Local Number 

TEL: 

816-472-5544 

FAX:  816-472-0959 

Toll Free Number 

TEL: 

800-467-6741 

Location 

6655 Troost Avenue 

Kansas City, MO 64131 

Website 

www.duracomm.com 

Email purchase order to 

[email protected] 

 

Summary of Contents for PSRM-1248NFPMU





















Reviews: