DuraComm HE1U-5012-BC-MU Product User Manual Download Page 23

   

23

   of   23   

August   3,   2016

 

 

LIMITED WARRANTY 

 

DuraComm  warrants  to  the  initial  end  user,  each  power  supply  manufactured  by  DuraComm  to  be  free  from  defects  in 

material and workmanship, when in normal use and service for a period of three years from the date of purchase, from an 
authorized DuraComm dealer. 

 

Should  a  product  manufactured  by  DuraComm  fail  or  malfunction  due  to  manufacturing  defect,  or  faulty  component, 
DuraComm,  at  its  option,  will  repair  or  replace  the  faulty  product  or  parts  thereof,  which,  after  examination  by 
DuraComm, prove to be defective or not operational according to specifications in effect at the time of sale to the initial 

end  user.    The  product  that  is  replaced  or  repaired  under  the  provisions  of  this  warranty,  will  be  warranted  for  the 
remainder of the original warranty period, only, and will not extend into a new three year warranty period. 

 

The limited warranty does not extend to any DuraComm product which has been subject to misuse, accidental damage, 
neglect, incorrect wiring not associated with manufacture, improper charging voltages, or any product which has had the 
serial number removed, altered, defaced, or changed in any way. 

 

DuraComm reserves the right to change, alter, or improve the specifications of its products at any time, and by so doing, 
incurs  no  obligation  to  install  or  retrofit  any  such  changes  or  improvements  in  or  on  products  manufactured  prior  to 

inclusion of such changes. 

 

DuraComm  requires  any  product  needing  in  or  out  of  warranty  service  to  be  returned  to  DuraComm.  All  requests  for 

warranty service must be accompanied by proof of purchase, such as bill of sale with purchase date identified.  DuraComm 
is  not  responsible  for  any  expenses  or  payments  incurred  for  the  removal  of  the  product  from  its  place  of  use, 
transportation or shipping expenses to the place of repair, or return expenses of a repaired or replacement product to its 

place of use. 

 

The implied warranties which the law imposes on the sale of this product are expressly LIMITED, in duration, to the three 
(3) year time period specified herein. DuraComm will not be liable for damages, consequential or otherwise, resulting from 
the use and operation of this product, or from the breach of this LIMITED WARRANTY. 

 

Some states do not allow limitations on the duration of the implied warranty or exclusions or limitations of incidental or 
consequential  damages,  so  said  limitations  or  exclusions  may  not  apply  to  you.    This  warranty  gives  you  specific  legal 

rights which vary from state to state. 

 

This  warranty  is  given  in  lieu  of  all  other  warranties,  whether  expressed,  implied,  or  by  law.    All  other  warranties, 

including  WITHOUT  LIMITATION,  warranties  of  merchantability  and  fitness  or  suitability  for  a  particular  purpose,  are 
specifically excluded.  DuraComm reserves the right to change or modify its warranty and service programs without prior 
notice. 

 
 

DuraComm

® 

Corporation 

6655 Troost Avenue 

Kansas City, MO 64131 

Phone (816) 472-5544   Fax (816) 472-0959  

www.duracomm.com 

Summary of Contents for HE1U-5012-BC-MU
























Reviews: