background image

ii

Safety Precautions

Operating Environment

Operate this unit in the following environment.
●  where the temperature range is between 5 and 35°C/41 and 95°F (-10 to +50°C/14 to 122°F in 

storage)

●  where the humidity range is between 20 and 85% RH (10 to 90% RH in storage, however no 

condensation)

●  which is not subject to direct sunlight
●  which is reasonably free from dust
●  which is subject to little or no vibration
●  which is free from air-borne salt
●  where there are no harmful chemicals
●  where the unit is not exposed to water

 

Keep this unit and the power cord away from heaters and heater vents.

Excessive heat could melt the cover or power cord covering, and result in a fire or an electrical shock.

 

Do not place metal objects or vessels containing liquids on top of the unit.

The entry of any metal object or liquid could result in a fire or an electrical shock.

 

Do not insert any metal or easily-combustible object inside this unit.

This could result in a fire or an electrical shock.

 

Do not use flammable sprays inside or near the unit (e.g. when cleaning the 

unit).

Such flammable gas may ignite and cause a fire or combustion.

 

Do not install this unit in a location where there is excessive humidity or where 

contact with water is possible.

Poor choice of location could result in deterioration of the insulation, a fire or an electrical shock.

 

Install this unit on a level, stable stand or floor, with sufficient space around it.

Failure to do so could result in the unit overturning and causing injury.

 

Disconnect the power plug from the power outlet before attempting to move 

this unit.

Failure to do so could result in power cord damage, a fire or an electrical shock.

 

Always disconnect the power plug from the power outlet when the unit is not 

to be used for an extended period.

Failure to do so could result in a fire due to leakage current if the insulation should deteriorate.

Summary of Contents for DF-755























































































Reviews: