Duplo DF-755 Instruction Manual Download

Page: 59 / 86

3-25

Chapter 3 ADVANCED OPERATION

Paper

Side guide

Paper set lever

36 mm/

1-1/2 inches

Raise the paper set lever and stack

the single-folded paper on the paper

feed table with the folded line facing

the non-operator's side.

The amount of paper stacked on the pa-

per feed table should be approximately

2/3 (approx. 36 mm/1-1/2 inches) of the

height of the side guide.

Loosen the fixing screws of the side

guides.

Side guide

Fixing screw

After pressing the side guide to each

side of the paper lightly, tighten the

screws to secure the side guides.

Paper set lever

Lower the paper set lever.

The paper feed table will be raised.

Make sure that you lower the paper set

lever. If you start operations without the

paper set lever lowered, the paper feed

rings will run idle, causing the machine

to stop.

Refer to Table of Rough Adjustment

Knob Positions to check the appro-

priate positions of first and second

folding plates.

Summary of Contents for DF-755























































































Search results

Summary of Contents for DF-755

Reviews:

Related manuals for DF-755

Brands by name

Popular brands

Duplo DF-755, Instruction Manual

Search results

Summary of Contents for DF-755

Reviews:

Related manuals for DF-755

Brands by name

Popular brands