Duplo DF-755 Instruction Manual Download

Page: 63 / 86

3-29

Chapter 3 ADVANCED OPERATION

Adjusting Fine Adjustment Knob of the Second Folding Plate

Folding Style

Fold Surface A

Adjustment

First folding plate

Fine adjustment knob

Single fold

The second folding plate is not used in single folding.

Double fold

Feeding direction

When B is

longer.

Turn the fine adjustment knob

counterclockwise.

When B is

shorter.

Turn the fine adjustment knob

clockwise.

Irregular

accordion

fold

Feeding direction

When B is

longer.

Turn the fine adjustment knob

counterclockwise.

When B is

shorter.

Turn the fine adjustment knob

clockwise.

Letter fold

Feeding direction

When B is

longer.

Turn the fine adjustment knob

clockwise.

When B is

shorter.

Turn the fine adjustment knob

counterclockwise.

Accordion

fold

Feeding direction

When B is

longer.

Turn the fine adjustment knob

clockwise.

When B is

shorter.

Turn the fine adjustment knob

counterclockwise.

Gate fold

Feeding direction

When B is

longer.

Turn the fine adjustment knob

clockwise.

When B is

shorter.

Turn the fine adjustment knob

counterclockwise.

Summary of Contents for DF-755























































































Search results

Summary of Contents for DF-755

Reviews:

Related manuals for DF-755

Brands by name

Popular brands

Duplo DF-755, Instruction Manual

Search results

Summary of Contents for DF-755

Reviews:

Related manuals for DF-755

Brands by name

Popular brands