background image

11 

 

The relevant temperature display continues to flash until 

the set temperature has been reached. The display then 
lights up constantly, and the alarm system is fully active 
again.  

 

INTERIOR LIGHT   

  
The interior light makes it easy to view your wine labels 

and  enhances  the  display  of  your  collection.  Touching 
the LIGHT mark toggles between 2 modes of operation 
for  the  internal  lights:  functional  (default)  mode  and 
showcase mode. If you are in functional (default) mode, 
the lights will turn on only when the door is open. If you 
are in showcase mode, the lights will  be on whether or 
not the door is open.  

 

 

The unit is  equipped with a LED light  fitting system. To 

change  the  LED  light  fitting  pls  contact  the  service 
department.  
 
If  your  model  is  provided  a  TriColor  lighting,  you  can 
select the color of interior light - amber, white and blue by 

touching  the 

Color  Selector

  key 

 .  Touching  the 

Color  selector

  key  toggles  between  single  color  mode 

and dynamic color mode. In the dynamic color mode the 
interior  light  will  start  to  cycle  through  the  3  available 
colors. Touching the 

Color Selector

 key once when the 

desired color is on, your interior light will be changed to 
that color. To change back to the dynamic color mode, 
touch the 

Color Selector

 key again

 

  

NOTE:

  Please  use  only  the  original  LED  light  fittings 

provided by the manufacturer.  

  

BOTTLE RACKS AND STORAGE

 

 

  

WARNING:

 Do not pull out more than  one loaded shelf 

at a time as this may cause the unit to tilt forward. Some 
shelves  are  designed  to  store  more  than  1  layer  of 
bottles. Such shelves are not allowed to slide if more than 
1 layer of bottles loaded on them.  

  

WARNING:

 Do not try to slide the shelves outwards 

beyond the fixed position to prevent the bottles from 
falling.  

  

WARNING:

 To prevent damaging the door gasket, make 

sure the door is fully open when pulling shelves out of the 
compartment.  

  

All the wine  racks slide out for easy  access, except for 
the bottom shelf. For easy access to the bottles stored, 
pull  the  rack  out  gently  until  it  stops.  The  shelves  are 
designed with an emergency stop to prevent them being 
removed too far when loaded.  

  

Many bottles may differ in size and dimensions. As such 

the  actual  number  of  bottles  you  may  be  able  to  store 
may vary.  

  

Bottle  capacities  are  approximate  maximums  when 

storing traditional Bordeaux 750 ML bottles and include 
bulk storage.  

  

You  may  load  your  wine  bottles  in  single  row  or  by 

stacking while taking note of the following - if you do not 

have enough bottles to fill your wine cellar, it is better to 
distribute  the  load  throughout  the  wine  cellar  so  as  to 
avoid “all on top” or “all below” type loads.  

-

 

Do remove or relocate adjustable wooden racks to 
accommodate larger type of bottles or increase the 
capacity of the cellar by stacking the bottles up when 
necessary. (See removing shelves)  

-

 

Keep small gaps between the walls and the bottles 
to  allow  air  circulation.  Like  an  underground  cellar 
air  circulation  is  important  to  prevent  mould  and 
promote a better homogeneous temperature.  

-

 

Do  not  overload  your  wine  cellar  to  facilitate  air 
circulation.  

-

 

Lay the bottles flat.  

-

 

Avoid obstructing the internal fans (located inside on 
the back panel of the unit).    

-

 

Do  not  cross  contaminate.  Store  only  wine  in  your 
unit to ensure that the environment is odor free.  

-

 

Only store wine in unopened bottles. Storing opened 
bottles may result in spillage.  
  

DYNAMIC CLIMATE / SILENT MODE  

  

This  Dynamic  Climate  mode  enables  the  relative 

humidity  inside  the  unit  and  the  temperature  to  be 
distributed evenly around the interior so you can store all 
your wine under exactly the same excellent conditions. If 
you would like to use the unit to store wine long term, the 
dynamic climate mode is a must. 

 
This will create a continuous climate in the cabinet which 

imitates that of a wine cellar.  
  
In the Dynamic Climate mode, the interior fan circulates 

the  inside  air  even  if  the  set  temperature  is  reached. 
Dynamic Climate mode is NOT the factory preset mode 
because  of  creating  noises  and  more  energy 
consumption.  To  change  to  Dynamic  Climate  mode, 
touch  and  hold  the  DOWN  key  for  approximately  five 
seconds.  The wine cellar will beep five times to confirm 
Dynamic Climate mode is on. To change back to default 
(Silent) mode (Also named as energy saving mode),  

touch  and  hold  the  UP  key  for  approximately  five 

seconds.  The wine cellar will beep three times to confirm 
default (Silent) mode is on.  

  

SABBATH MODE  

  
Sabbath mode is available for the observance of certain 

religious  holidays.  This  mode  turns  off  the  displays, 
interior light and audible alarms and prevents them from 
turning on again. Normal cooling operations will still take 
place.  

  
To initiate Sabbath mode, press the POWER and LIGHT

 

keys  at  the  same  time  for  at  least  5  seconds.  The 
indicator  light  will  flash  four  times  and  confirm  the 
Sabbath mode is ON.  

  
Sabbath  mode  can  be  exited  by  repeating  the  above 

process. The Sabbath Mode will automatically exit after 
96 hours.  

  

ECO DEMO MODE  

  

Summary of Contents for DAUF-16.52
















Reviews: