background image

3

Installation and Operation of: 

FlexBake 5™ Integrated Ventilation System

In addition to the warnings and cautions in this manual, use the following guidelines for 

safe operation of the unit.

•  Read all instructions before using equipment.
•  For your safety, the equipment is furnished with a properly grounded cord connector. Do  
  not attempt to remove or disconnect the grounded connector.
•  Install or locate the equipment only for its intended use as described in this manual. 
•  Do not use corrosive chemicals on this equipment.
•  Do not operate this equipment if it has a damaged cord or plug, if it is not working  

 

  properly, or if it has been damaged or dropped.
•  This equipment should be serviced by qualified personnel only. Contact the nearest   

 

  Duke authorized service facility for adjustment or repair.
•  Do not block or cover any openings on the unit.
•  Do not immerse cord or plug in water.
•  Keep cord away from heated surfaces.
•  Do not allow cord to hang over edge of table or counter.
•  A minimum clearance of 6” (152,4 mm) from the top of the unit to the ceiling must be 

provided.

The following warnings and cautions appear throughout this manual and should be 

carefully observed.

•  Turn the unit off, disconnect the power source and allow unit to cool down before   

 

  performing any service or maintenance on the unit.
•  The procedures in this manual may include the use of chemical products. You must read   
  the Material Safety Data Sheets before using any of these products. 
•  The unit should be grounded according to local electrical codes to prevent the  

 

 

  possibility of electrical shock. It requires a grounded receptacle with dedicated electrical   
  lines, protected by fuses or circuit breaker of the proper rating, in accordance with all  

 

  applicable regulations.
•  Disposal of the unit must be in accordance with local environmental codes and/or any    
  other applicable codes.
•  This appliance is not intended for use by persons (including children) with reduced  

 

  physical, sensory or mental capabilities, or lack of experience and knowledge, unless  

 

  they have been given supervision or instruction concerning use of the appliance    

 

  by a person responsible for their safety.

Summary of Contents for FlexBake 5 IVS-208-FB5













Reviews: