background image

Page 3

This garage door opener has been designed and tested to offer safe service provided it is installed, ope-
rated, mantained and tested in strict accordance with the instructions and warnings contained in this
manual.

Please, carefully reat this instruction manual before to procede with installation of your garage door ope-
ner, and make sure that weight , dimension and type of your garage door are within the limits of your
garage door opener model. 

The structure of the door and  the wall/pillars must be safe and stabile.
Install garage door opener only on properly balanced and lubricated  garage door.
All repairs to  cables, spring assemblies and other hardware must be made by a trained and professional
door systems technician BEFORE installing the garage opener

To prevent possible serious injury or death: always call a trained and certified door systems tecnician if
garage door binds, sticks or is out of balance. 

An unbalanced garage door may not reverse when required and could result  in serious injury or
death !

Never try to loosen, moove or adjust garage door, door springs, cables pulleys, bracketts or their har-
dware, all of wich  are under EXTREME tension.

Disable all locks and remove all ropes connected to garage door  before installing and operating garage
door opener to avid entanglement.

To prevent damage  to garage door and opener: Always disable locks before installing and operating the
opener.

Never wear watches, rings, or loose clothing while installing or servicing  opener. They could be caught
in garage door opener mechanisms.

Place entrapment warning labels on wall next to garage door control.

Place manual release/safety reverse label in plain view on inside of garage door.

Upon completion of installation, test that your garage door opener is  corretly working and test safety
reversal system. door must reverse  on contact with an object on the floor.

In order to prevent  injuries:

Never leave childrens without parental control in proximity  of a garage door opener in motion open, clo-
sed or stopped.

Never permit children  to play with remote control push buttons or transmitters of garage door opener
and prevent childrens to operate the garage door opener  by control push buttons or transmitters
.Always keep remote controls out of reach of children.

Install wall-mounted garage door controls ( optionals) out of reach of children and away of moving parts
of the door.

Activate door  only when it can be seen clearly, is properly adjusted and there are no obstructions to
door travel.
Always keep garage door in sight until completely closed. 

Very Important Safety 

WARNINGS

!

!

Summary of Contents for 8500 SF























Reviews: