1. Introduction
The BLUE 232 gate controller is used to control the drives of double-leaf gates, powered by
alternating voltage 230V, 50Hz, with a power of max. 2 x 350W. It works with actuators equipped with limit
switches or encoders. The driver configuration is done via the Blue Motor Control application for Android
devices, available for download from the GooglePlay store. The application communicates with the
controller via Bluetooth. The software has an intuitive interface, thanks to which the configuration is quick
and efficient.
The controller has the function of slowing down the movement while stopping and regulating the power of
the actuators. The control panel allows you to set automatic closing of the gate after a time and / or photo-
closing (activated after the photocells are violated and released again). BLUE 232 has an output for a 12 /
24V DC gate bolt and an additional output controlled by a manual or radio button, which can work in
bistable or monostable mode, intended for switching an external device. Radio control takes place via the
DTM433MHz and DTM868MHz series transmitters.
2. Technical data
Basic parameters
•
Power supply
230V AC, 50 Hz
•
Stanby power consumption
5W
•
Operating temperature (min./max.)
-20°C /+55°C
•
External dimensions of the casing (W x D x H)
240 x 120 x 190 mm
•
Mounting method
surface-mounted housing
•
Weight
1,1 kg
•
IP
66
Outputs / inputs
•
Actuator output (voltage / maximum power /
built-in capacitor / quantity)
230VAC / 2 x 350W / none / 2
•
Signal lamp output
OC max. 24VDC/6W
•
Peripheral power supply output (photocells, lock, etc.)
24V DC, 0,5A
•
Power output for photocell transmitters
OC type (see PHOTO-TEST function)
•
Gate bolt output
12 / 24V DC, switched for 5 sec. when opening begins
•
Additional output in bistable / monostable mode
relay (potential-free), max. 1A / 30V AC / DC
•
Photocell inputs / quantity
programmable, NC type / 3
•
Manual control input A, B, C
programmable, NO type
•
Manual control STOP input
NC type
•
Limit switches input
on opening and closing / NC type / 4
•
Motor encoder input
digital / 2
Control part
•
Adjustable opening and closing time / soft stop phases
1 - 120s / 0 - 15s with an accuracy of 1s
•
Adjusting the power of the actuators
10-100 separately for the 1st and 2nd actuators, via the app
•
Increasing the programmed power of actuators
yes, separately for each actuator 0-50%
•
Second leaf delay adjustment
yes, time adjustable separately for opening and closing 0-60s
•
Programming the controller operation
using Bluetooth application
•
Gate auto-closing function
yes, time adjustable from 1 to 120s
•
Photo-closing function
yes, time separately adjustable 0-120s
•
Pushing with increased force after closing,
start with increased force
programmable
•
Preliminary operation of the signal lamp
programmable, 5s
•
Photocell test (testing of photocells before door movement) programmed separately for each photocell input
•
User Interface
SW button, LED indicators, application for configuring the controller
operating parameters via Bluetooth
™
•
Device configuration memory
non-volatile
Radio part
•
Frequency
433MHz and 868MHz
•
Antenna input impedance
50
W
•
Antennas
wire, terminals for connecting external antennas
•
Memory capacity
200 remotes, each with an individual number in memory
•
Remote configuration
assigning the controller function to any remote control button
•
Possibility to erase all memory
yes
•
Possibility to delete a single remote control
yes
•
Possibility to add a remote control without interfering
with the controller
yes, the function of remote assigning the remote control
/ via Bluetooth ™Bluetooth
™
•
Blocking the remote assigning function
yes
T
echnical data / Introduction
3