manualshive.com logo in svg

Dspecialists ISOSTEM Expert, User Manual

Share
Download
Dspecialists ISOSTEM Expert User Manual Download Page 5

ISOSTEM     USER MANUAL

Safety Instructions     5

S

AFETY

I

NSTRUCTIONS

This symbol, wherever it appears, alerts you to the
presence of uninsulated dangerous voltage inside the
enclosure – voltage that may be sufficient to constitute
a risk of shock.

This symbol, wherever it appears, alerts you to im-
portant operating and maintenance instructions in the
accompanying literature. Read this manual.

CAUTION: To reduce the risk of electrical shock, do not remove any
screws of the enclosure. There are no user serviceable parts inside. Refer
servicing to qualified personnel only.

WARNING: To reduce the risk of fire or electrical shock, do not expose this
appliance to rain or moisture.

1.  To assure best performance, please read this manual carefully.

2.  Connect this appliance to a grounded AC outlet of 90 V to 250 V,

47 Hz to 63 Hz.

3.  Keep the power cord in good condition. If the power cord becomes

damaged, discard and replace it. Never isolate the ground of the AC
power cord.

4.  The power fuses are located on the rear panel of the appliance and

may be accessed from the outside. In case the fuses have to be ex-
changed only use fuses of the same type as labeled.

5.  The power switch of the device is located on the front panel of the

appliance. The ON and OFF states are marked by “1” and “0” re-
spectively.

6.  Install this unit in a well ventilated, cool, dry and clean place. Keep it

away from direct sunlight, heat sources, vibration, dust, moisture, or
cold. In a cabinet allow about 2.5 cm of free space all around this
unit for adequate ventilation.

7.  The appliance must be adapted slowly to extreme temperature

changes. These extreme changes may cause moisture inside that
can cause failure and/or electrical shock.

8.  Prolonged exposure to high volume levels may cause hearing dam-

age and/or loss. The use of hearing protection in high volume situa-
tions is recommended.

Summary of Contents for ISOSTEM Expert






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands