DSC LE2080 Installation Manual Download Page 38 | Manualshive

Page: 38 / 60

background image

Event [Section] Label

Default Label

Event [Section] Label

Default Label

[869] Keypad Message

(Keypad Message)

[870] Function Successful (Successful)

[871] Function Failure

(Unsuccessful)

[872] Invalid Command

(Invalid Command)

[873] System Stay Armed (Stay Armed)

[874] System Away Armed (Away Armed)

[875] System Night
Armed

(Night Armed)

[876] System Disarmed
Ready

(Disarmed Ready)

[877] System Disarmed,
Not Ready

(Disarmed Not Ready)

[878] System In Alarm

(is in Alarm)

[879] Trouble Label

(Service is Required)

[880] No Alarms in
Memory

(No Alarms in Memory)

[881] Pay As You Go
Balance

(Pay as you go balance:)

[882] Pay As You Go
Message

(*123#)

[883] Response Code

(Response Code)

Receiver Diagnostic Testing

[901] Diagnostic Test Transmission

[1] Ethernet 1

Default (OFF).

[2] Ethernet 2

Default (OFF).

[3] Cellular 1

Default (OFF).

[4] Cellular 2

Default (OFF).

[5],[6],[7],[8] Reserved

(OFF).

This section may be used by the installer to force the communicator to send an immediate test trans-
mission to specific receivers, to verify that the communications paths are available. Diagnostic test trans-
mission failure will indicate as FTC trouble (yellow LED = 9 flashes). If an FTC error occurs when testing
all receivers, select only one receiver and repeat test to isolate the receiver that is not communicating.

NOTE:

Sending a test transmission to a receiver that is not programmed generates an FTC trouble.

[961] Cellular Inactivity Timeout

Default (41) Valid entries are 00 - FF.

[962] CREG Max Registration

Default (C8) Valid entries are 00 - FF.

[963] Retransmission Delay

Default (2D) Valid entries are 00 - FF.

[964] Voice Volume

Default (04) Valid entries are 00 - FF.

[965] Microphone Gain

Default (01) Valid entries are 00 - FF.

[966] SMS Recovery Hour

Default (0018) Valid entries are 0000 - FFFF.

[967] SMS Threshold 1

Default (0032) Valid entries are 0000 - FFFF.

[968] SMS Threshold 2

Default (0064) Valid entries are 0000 - FFFF.

[969] Debug Mask Timeout

Default (2760) Valid entries are 0000 - FFFF.

[970] Monitoring Heartbeat

Default (0060) Valid entries are 0000 - FFFF.

System Information (Read Only)

NOTE:

Sections [971] - [998] are provided for information (read-only). Values in these sections cannot

be modified by the installer.

38

«
...
36
37
38
39
40
...
»

Summary of Contents for LE2080





























































Reviews:

No comments

Related manuals for LE2080

Brand: QMobile Pages: 66

Brand: Lanix Pages: 13

Brand: Lanix Pages: 25

Brand: Groov-e Pages: 2

Brand: lepow Pages: 2

Brand: Audiovox Pages: 44

Brand: Kogan Pages: 22

Brand: Nordmende Pages: 40

Brand: Icemobile Pages: 11

Brand: Samsung Pages: 223

Brand: Samsung Pages: 101

Heaven SCH-U320

Brand: Samsung Pages: 174

Brand: Samsung Pages: 108

Brand: Samsung Pages: 152

Brand: Samsung Pages: 30

Brand: GENERAL MOBILE Pages: 53

Brand: Emerson Pages: 114

Brand: Sharp Pages: 140

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands