DSC LE2080 Installation Manual Download Page 53

Page: 53 / 60

[818] Zone Bypassed

Default (Zone Bypassed)
_______________________________________

[819] Zone Unbypassed

Default (Zone Unbypassed)
_______________________________________

[820] Burglary Verified

Default (Burglary Verified)
_______________________________________

[821] Burglary Not Verified

Default (Burglary Not Verified)
_______________________________________

[822] Alarm Cancelled

Default (Alarm Cancelled)
_______________________________________

[823] Holdup Verified

Default (Holdup Verified)
_______________________________________

[824] Walk Test Begin

Default (Walk Test Begin)
_______________________________________

[825] Walk Test End

Default (Walk Test End)
_______________________________________

[826] System Test

Default (Test Message)
_______________________________________

[827] Periodic Test Transmission

Default (Periodic Test)
_______________________________________

[828] Periodic Test With Trouble

Default (Periodic Test With Trouble)
_______________________________________

[829] DLS Remote Programming Begin

Default (Remote Programming Begin)
_______________________________________

[830] DLS Remote Programming End

Default (Remote Programming End)
_______________________________________

[831] SA Remote Programming Begin

Default (Remote Programming Begin)
_______________________________________

[832] SA Remote Programming End

Default (Remote Programming End)
_______________________________________

[833] Installer Lead In

Default (Local Programming Begin)
_______________________________________

[834] Installer Lead Out

Default (Local Programming End)
_______________________________________

[835] Firmware Update Begin

Default (Firmware Update Begin)

_______________________________________

[836] Firmware Update Successful

Default (Firmware Update Successful)
_______________________________________

[837] Firmware Update Fail

Default (Firmware Update Fail)
_______________________________________

[838] Delinquency

Default (Delinquency)
_______________________________________

[839] Keypad Lockout

Default (Keypad Lockout)
_______________________________________

[840] Event Log 75% full

Default (Event Log Near Full)
_______________________________________

[841] FTC Trouble

Default (fail to communicate trouble)
_______________________________________

[842] FTC Restore

Default (fail to communicate restore)
_______________________________________

[843] Panel Absent Trouble

Default (Panel Communications Trouble)
_______________________________________

[844] Panel Absent Trouble Restore

Default (Panel Communications Restore)
_______________________________________

[845] Module Reprogramming

Default (Communicator Programming Updated)
_______________________________________

[846] Firmware Update

Default (Communicator Programming Updated)
_______________________________________

[850] Module

Default (Module)
_______________________________________

[851] Stay Arm

Default (Stay Arm)
_______________________________________

[852] Away Arm

Default (Away Arm)
_______________________________________

[853] Night Arm

Default (Night Arm)
_______________________________________

[854] Disarm

Default (Disarm)
_______________________________________

[855] Activate Command Output 1

Default (Activate Command Output 1)
_______________________________________

Summary of Contents for LE2080





























































Search results

Summary of Contents for LE2080

Reviews:

Related manuals for LE2080

Brands by name

Popular brands

DSC LE2080, Installation Manual

Search results

Summary of Contents for LE2080

Reviews:

Related manuals for LE2080

Brands by name

Popular brands