background image

l

Remote Diagnostics

l

Panel Format Detection

l

SMS Command and Control

l

Phone number call direction

l

Easy enrollment with C24 Communications via VRU, web or mobile interface

NOTE:

The 3G4010CF is designed to work with the Contact ID communication format as described in SIA DC- 05 Standard or

the SIA communication format as described in SIA DC-03 Standard. Before completing the field installation of the alarm mon-
itoring system, please ensure communication with the supervising station is successful by sending several events and con-
firming that they have been received.

Technical Specifications

Ratings

Power Supply Ratings

Input Voltage:

120V/60Hz/0.3A

Standby Voltage:

12V/7AH

Standby Time:

24h (NSC) plus 5 minutes alarm

Low Battery Trouble
Indication Threshold:

11.5VDC

Battery Deep Discharge
Protection (cut-off):

9.5VDC

Battery Type:

sealed, rechargeable type, rated 12V/7Ah

(for 24hr standby time)

Battery charging voltage:

13.75Vdc

Battery charge current:

700mA (maximum)

NOTE: Battery must be replaced every 3-5 years.
Operating frequency - 2G
(GSM/GPRS/EDGE):

850/1900MHz

Operating frequency - 3G
(UMTS/HSPA):

850/1900MHz

Antenna gain:

2.0dBi

Environmental
Specifications

Operating temperature:

0°C-49°C (32°F-120°F)

Humidity:

93%RH Maximum (non-condensing)

Mechanical Specifications

Enclosure Type

metal, red, hardwired transformer and high voltage connection box included

Enclosure Dimensions:

290mm x 254mm x 75mm (11.5" x 10" x 3")

Weight:

5.8Kg (12.8 lbs) (including standby battery)

Simulated Telco Loop specifications (TIP/RING)

On-Hook Voltage:

12Vdc

Off-Hook Voltage
(Maximum):

22Vdc

Loop Current :

25mA

Loop Resistance :

600 Ohms

Standard Battery Capacity

The calculation for battery capacity is based on 200mA standby current for 24 hours plus a five minute alarm at 400mA or
600mA (if the 4 PGM outputs are also activated)
The requirements are as follows:
200mA x 24h = 4800mAh capacity for standby
400mA x 5/60h= 33.33mAh capacity for alarm condition
Total = 4833.33 mAh needed for 24h and five minutes alarm transmission. The supplied battery is 7Ah.

4

Summary of Contents for 3G4010CF

























Reviews: