Frequency Band
3G4010CF
PCS1900 / FDD II
3.76 dBi
Thistransmitter must not be co-located or operating in conjunction with anyother
antenna or transmitter.
Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC
pour un environnement non contrôlé. L'antenne doit être installé de façon à
garder une distance minimale de 20 centimètres entre la source de ray-
onnementset votre corps. Gain de l'antenne doit être ci-dessous:
Bande de fréquence
3G4010CF
GSM850 / FDD V
6.21 dBi
PCS1900 / FDD II
3.76 dBi
L'émetteur ne doit pasêtre colocalisé ni fonctionner conjointement avec à autre
antenne ou autre émetteur.
FCC CLASS B DIGITAL DEVICE NOTICE
Thisequipment hasbeen tested and found to complywith the limitsfor a ClassB
digitaldevice, pursuant to part 15 of the FCC Rules. These limitsare designed to
provide reasonable protection against harmfulinterference in a residential install-
ation. This equipment generatesuses and can radiate radio frequencyenergy
and, if not installed and used in accordance with the instructions, maycause harm-
fulinterference to radio communications. However, there isno guarantee that
interference willnot occur in a particular installation. If thisequipment doescause
harmfulinterference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference byone or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different fromthat to which the
receiver isconnected.
•Consult the dealer or an experienced radio/TVtechnician for help
CAN ICES-3 (B) / NMB-3 (B)
ThisClassBdigitalapparatuscomplieswith Canadian ICES-003.
Cet appareilnumérique de classe Best conforme à la norme canadienne ICES-
003.
FCC ID:F53143G4010
3G4010 Product Identifier US: F5314MO00B3G4010
REN: 0.0B
USOC Jack: RJ-31X
WARNING: To satisfy FCC RF exposure requirements for mobile trans-
mitting devices, a separation distance of 20cm or more must be main-
tained between the antenna of this device and persons during device
operation.
Telephone Connection Requirements
Aplug and jack used to connect thisequipment to the premiseswiring and tele-
phone network must complywith the applicable FCC Part 68 rules and require-
mentsadopted by the ACTA. A compliant telephone cord and modular plug is
provided with thisproduct. It isdesigned to be connected to a compatible mod-
ular jackthat isalso compliant. See installation instructionsfor details.
Ringer Equivalence Number (REN)
The REN isused to determine the number of devicesthat maybe connected to a
telephone line. Excessive RENs on a telephone line mayresult in the devicesnot
ringing in response to an incoming call.
In most but not allareas, the sumof RENsshould not exceed five (5.0). To be cer-
tain of the number of devices that may be connected to a line, asdetermined by
the total RENs, contact the local Telephone Company. For productsapproved
after July 23, 2001, the REN for this product is part of the product identifier that
hasthe format. US: AAAEQ##TXXXX. The digits represented by## are the REN
without a decimalpoint (e.g., 03 isa REN of 0.3). For earlier products, the REN is
separatelyshown on the label.
Incidence of Harm
If this equipment 3G401CF causes harm to the telephone network, the tele-
phone companywill notifyyou in advance that temporary discontinuance of ser-
vice may be required. But if advance notice is not practical, the Telephone
Companywillnotifythe customer assoon as possible. Also, you willbe advised of
your right to file a complaint with the FCC if you believe it isnecessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, oper-
ationsor proceduresthat could affect the operation of the equipment. If thishap-
pens the Telephone Company will provide advance notice in order for you to
make necessarymodificationsto maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment for repair or warranty information,
please contact the facilityindicated below. If the equipment iscausing harmto the
telephone network, the Telephone Companymay request that you disconnect
the equipment untilthe problemis solved. This equipment is of a type that isnot
intended to be repaired bythe end user.
DSC c/o APL Logistics, 757 DouglasHillRd., Lithia Springs, GA30122
Additional Information
Connection to partyline service issubject to state tariffs. Contact the state public
utilitycommission, public service commission or corporation commission for
information. Alarm dialling equipment must be able to seize the telephone line
and place a call in an emergency situation. It must be able to do thiseven if other
equipment (telephone, answering system, computer modem, etc.) already has
the telephone line in use. To do so, alarmdialling equipment must be connected
to a properlyinstalled RJ-31Xjackthat is electricallyin serieswith and ahead of all
other equipment attached to the same telephone line. Proper installation isdepic-
ted in the figure below. If you have anyquestions concerning these instructions,
you should consult your telephone company or a qualified installer about
installing the RJ-31Xjackand alarmdialling equipment for you.
Industry Canada Compliance Statement
ThisEquipment meetsthe applicable IndustryCanada TerminalEquipment Tech-
nical Specifications. This is confirmed by the registration number. The abbre-
viation, IC, before the registration number signifies that registration was
performed based on a Declaration of Conformityindicating that IndustryCanada
technical specifications were met. It does not imply that that Industry Canada
approved the equipment. The Ringer Equivalence Number (REN) for this ter-
minalequipment is 0.0. The REN assigned to each terminal equipment provides
an indication of the maximumnumber of terminals allowed to be connected to a
telephone interface. The termination on an interface may consist of any com-
bination of devices subject only to the requirement that the sum of the Ringer
Equivalence Numbersof alldevicesdoesnot exceed 5.
IC:160A-3G4010
Cet équipement est conforme aux spécifications techniques applicables aux
équipements terminaux d'Industrie Canada. Ceci est confirmé par le numéro
d'enregistrement. L'abréviation IC précédant le numéro d'enregistrement signifie
que l'enregistrement a été effectué sur la base de la Déclaration de conformité
indiquant que le produit est conforme aux spécificationstechniques d'Industrie
Canada. Cecin'implique pasque le produit ait été approuvé par Industrie
Canada.
Le nombre équivalent de sonneries (REN) de cet appareilterminal est 0.0. Le
REN attribué à chaque équipement terminalfournit une indication sur le nombre
maximumde terminauxpouvant être connectéssur une interface téléphonique.
La terminaison sur une interface peut constituer en n'importe quelle combinaison
d'appareils, à la condition seulement que la somme desNombreséquivalentsde
sonneriesde touslesappareilsne soit passupérieure à 5.
This Class B digital apparatus meets all requirements of the Canadian inter-
ference-causing equipment regulations. Cet appareilnumérique de la Classe B
respecte touteslesexigencesde règlement sur le matérielbrouilleur du Canada.
The term “IC:” before the radio certification number only signifies that Industry
Canada technicalspecificationswere met.
NIST Validation of encryption algorithmAES128 certificate No. 3161
Warranty
DigitalSecurityControlswarrantsthe originalpurchaser that for a period of twelve
monthsfromthe date of purchase, the product shallbe free of defectsin mater-
ials and workmanship under normal use. During the warranty period, Digital
SecurityControlsshall, at its option, repair or replace anydefective product upon
return of the product to its factory, at no charge for labour and materials. Any
replacement and/or repaired parts are warranted for the remainder of the ori-
ginal warranty or ninety (90) days, whichever is longer. The original purchaser
must promptlynotifyDigitalSecurityControlsin writing that there isdefect in mater-
ialor workmanship, such written notice to be received in all eventsprior to expir-
ation of the warranty period. There is absolutelyno warrantyon software and all
software products are sold as a user license under the terms of the software
license agreement included with the product. The Customer assumesallrespons-
ibility for the proper selection, installation, operation and maintenance of any
products purchased from DSC. Custom products are only warranted to the
extent that theydo not function upon delivery. In such cases, DSC can replace or
credit at itsoption.
International Warranty
The warranty for international customers isthe same asfor any customer within
Canada and the United States, with the exception that Digital SecurityControls
shallnot be responsible for anycustomsfees, taxes, or VAT that maybe due.
Warranty Procedure
To obtain service under this warranty, please return the item(s) in question to the
point of purchase. All authorized distributors and dealers have a warranty pro-
gram. Anyone returning goods to Digital Security Controls must first obtain an
authorization number. DigitalSecurityControlswillnot accept anyshipment what-
soever for which prior authorization hasnot been obtained.
22
