DRUCK TEMPERATUR
&
Leitenberger GmbH •
Bahnhofstr. 33 • D-72138 Kirchentellinsfurt • GERMANY
Tel. +49 (0) 7121-90920-0 • Fax +49 (0) 7121-90920-99 • [email protected] •
DT
www.druck-temperatur.de
MANUAL
TLDMM
Referezdruckmessgerät
2.0
TLDMM
reference pressure gauge
2.0
50
SET N
cl
TI G Cy e opera ve Mode
Command LA000RTA<cr>
R = '0' rep
s e
le eeping the se ngs, R = '1' resets the
eat th last cyc k
set n
d
gs an st
n
oo
I ch
arts ew l p, (1 ASCI
aracter),
T = ‘0’ the temperature is not recor
alog.
ded in the dat
T = ‘1’ the temperature is recor d b
alog, (1 ASCIII
de y the dat
character),
A = manual p
m
u oma c capture mode, (1
'0'
ca ture ode, A = '1' a t
ASCII character).
Answer
LB000RTA<cr>
READ Cycle o
a ve
per
Mode
Command LB000RTA<cr>
R - '0' repeats the last loop keepin the se
t e
g
ngs, R . . . resets h
se ngs and st
oo (1
).
arts new l p, ASCII character
The temper
re n
ded in the datalog.
atu is ot recor
The temperature is recorded b th d alog, (1 AS I ch
er).
y e at
CII
aract
A - '
ture m e,
0' manual cap
od A - '0' autom
a ture m e,
a c c p
od (1
ASCII character).
Answer
LB000RTA<cr>
Da
e
talog subcycl ind xe
N
e s READI G
Command L>000
cr
0CC< >
CC s
: ub
le
cyc ma e rom
o '4'
d f
'0' t (2
ers).
ASCII charact
NN NNN: N mbe o ca t res
de n he C
c
N
u
r f p u
ma
i t C sub ycle (6 ASCII
characters).
Answer L>NNNNNNCC<cr>
SETTING UP AND STARTING THE DATALOGGER
Set the type of datalog that you want to run by using the
command. If you want to clear
LA000RTA
the old datalog and start a new datalog with new parameters, set R = 1. If you want to con nue
the previouse one, set R = 0.
In the case of automa c datalog, set the capture interval with the
command and then
L4HHMMSS
set the total number of captures with the
command.
L5NNNNNN
Example:
=> t1 = 5 minutes, capture interval
L4000500<cr>
=> NNNNNN = 11 captures
L5000011<cr>
Take into account the formular for calcula ng the total me t2 = [(NNNNNN-1)*t1] = (11-1)*5
= 50 minutes. Start the capture cycle with the command
. Stop the cycle with the
L000000<cr>
L1000000<cr>
L2000000
command. Check the progress of the cycle with the
<cr> command.
DATA CONTROL AND TRANSMISSION
Check the total number of captures made with the
command. Check the general
L2000000<cr>
se ngs of the last datalog made with the
command. Check the par al indexes of
L3000000<cr>
sub-cycles made with the
command. With the L70000CC command you can control
L>0000CC<cr>
the start date and me of each indivicual sub-cycle.
With the command
the tool begins the procedure of sending the recorded data with
L6000000<cr>
the transmission of the data of index 0. To con nue the transmission and to get the subsequent
indexes, send the command
. The instrument will respond with the sending of the data of
@<cr>
the next index. Repeat sending the command
to the desired index. Complete the procedure
@<cr>
with teh command
.
;<cr>
