manualshive.com logo in svg

Draytek VigorAP 910C, User Manual

Share
Download
Draytek VigorAP 910C User Manual Download Page 103

 

VigorAP 910C User’s Guide 

93

Antenna 

VigorAP 910C can be attached with two antennas to have good 
data transmission via wireless connection. However, if you 
have only one antenna attached, please choose 1T1R. 

 

Tx Power 

The default setting is the maximum (100%). Lower down the 
value may degrade range and throughput of wireless. 

 

Channel Width 

Auto 20/40 MHZ– 

the device will use 20Mhz or 40Mhz for 

data transmission and receiving according to the station 
capability. Such channel can increase the performance for data 
transit. 

20 MHZ- 

the device will use 20Mhz for data transmission and 

receiving between the AP and the stations. 

40 MHZ- 

the device will use 40Mhz for data transmission and 

receiving between the AP and the stations. 

After finishing this web page configuration, please click 

OK 

to save the settings. 

Summary of Contents for VigorAP 910C
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands