manualshive.com logo in svg

Dover PSG WILDEN SANIFLO PS2 Series, Engineering, Operation & Maintenance

Share
Download
Dover PSG WILDEN SANIFLO PS2 Series Engineering, Operation & Maintenance Download Page 23

 

WIL-12330-E-08

 

Wilden

® 

23 

Disassembly / Reassembly

 

 

Shaft Seal Installation

 

Pre-Installation

 

Once all of the old seals have been removed, the inside of the 

bushing should be cleaned to ensure no debris is left that may 

cause premature damage to the new seals.

 

 

Installation

 

1.

 

Wrap electrical tape around each leg of the needle-nose 

pliers (heat shrink tubing may also be used). This is done 

to prevent damaging the inside surface of the new seal. 

2.

 

With a new seal in hand, place the two legs of the needle-

nose pliers inside the seal ring. (See Figure A.) 

3.

 

Open the pliers as wide as the seal diameter will allow, 

then with two fingers pull down on the top portion of the 

seal to form a kidney shape. (See Figure B.) 

4.

 

Lightly clamp the pliers together to hold the seal into the 

kidney shape. Be sure to pull the seal into as tight of a 

kidney shape as possible, this will allow the seal to travel 

down the bushing bore easier. 

5.

 

With the seal clamped in the pliers, insert the seal into the 

bushing bore and position the bottom of the seal into the 

correct groove. Once the bottom of the seal is seated in 

the groove, release the clamp pressure on the pliers. This 

will allow the seal to partially snap back to its original 

shape. 

6.

 

After the pliers are removed, you will notice a slight bump 

in the seal shape. Before the seal can be properly resized, 

the bump in the seal should be removed as much as 

possible. This can be done with either the Phillips 

screwdriver or your finger. With either the side of the 

screwdriver or your finger, apply light pressure to the peak 

of the bump. This pressure will cause the bump to be 

almost completely eliminated. 

7.

 

Lubricate the edge of the shaft with NLGI grade 2 white EP 

bearing grease. 

8.

 

Slowly insert the center shaft with a rotating motion. This 

will complete the resizing of the seal. 

9.

 

Perform these steps for the remaining seals.

 

 

 

 

Tools

 

The following tools can be used to aid in the installation of the 

new seals:

 

•

 

Needle-Nose Pliers  

•

 

Phillips Screwdriver  

•

 

Electrical Tape

 

 

 

Figure A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure B

 

 

 

 

 

Summary of Contents for PSG WILDEN SANIFLO PS2 Series





































Reviews:

No comments

Brands by name

Popular brands

Load more brands