manualshive.com logo in svg

Dover PSG WILDEN SANIFLO PS2 Series, Engineering, Operation & Maintenance

Share
Download
Dover PSG WILDEN SANIFLO PS2 Series Engineering, Operation & Maintenance Download Page 16

 

WIL-12330-E-08

 

Wilden

® 

16 

Disassembly / Reassembly

 

 

 

Step 10A

 

 

Next, remove the liquid chamber from the 

center section assembly. 

Step 10B

 

 

 

If your pump is fitted with an integral piston 

diaphragm (IPD), when you remove the 

liquid chamber you will notice that there is 

no outer piston. 

Step 11A

 

 

 

Using two (2) adjustable wrenches, turning 

in the opposite direction, loosen and 

remove one of the two outer pistons. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Step 11B

 

 

 

If your pump is fitted with an IPD, the 

procedure for removing the diaphragm is 

slightly different. In this case, simply grasp 

the diaphragm in two locations and turn in a 

counterclockwise direction. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Step 12A

 

 

 

After loosening and removing the outer 

piston, the remaining diaphragm assembly 

and shaft can be removed from the center 

section assembly.. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Step 12B

 

 

 

If your pump is fitted with an IPD, the 

procedure for removing the diaphragm is 

the same. 

 

 

 

Summary of Contents for PSG WILDEN SANIFLO PS2 Series





































Reviews:

No comments

Brands by name

Popular brands

Load more brands