manualshive.com logo in svg

Dover PSG WILDEN SANIFLO PS2 Series, Engineering, Operation & Maintenance

Share
Download
Dover PSG WILDEN SANIFLO PS2 Series Engineering, Operation & Maintenance Download Page 15

 

WIL-12330-E-08

 

Wilden

® 

15 

 

Disassembly / Reassembly

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Step 4

 

 

Next, remove the clamp bands 

that secure the ball valve 

housing to the liquid chamber. 

Step 5

 

 

 

Next, remove the ball valve 

housing, valve ball and gasket. 

Step 6

 

 

 

Loosen the wing nut and remove the 

inlet manifold clamp bands.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Step 7

 

 

Next, remove the clamp bands that 

secure the ball valve housing to the 

liquid chamber. 

Step 8

 

 

 

Next, remove the ball valve 

housing, valve ball and gasket 

from liquid chamber. To ensure 

proper alignment during 

reassembly of manifold/liquid 

chamber interface, turn off-set 

portion of valve housing to the left 

or to the right. This procedure 

works for the inlet manifold and 

discharge manifold connections. 

Step 9

 

 

 

Now the large clamp bands can be 

removed.  

NOTE: 

Prior to assembly, 

alignment marks should be 

placed on the liquid chambers 

and air chambers to assist  

with proper alignment during 

reassembly. 

 

Summary of Contents for PSG WILDEN SANIFLO PS2 Series





































Reviews:

No comments

Brands by name

Popular brands

Load more brands