manualshive.com logo in svg

Dover PSG WILDEN SANIFLO PS2 Series, Engineering, Operation & Maintenance

Share
Download
Dover PSG WILDEN SANIFLO PS2 Series Engineering, Operation & Maintenance Download Page 19

 

WIL-12330-E-08

 

Wilden

® 

19 

Disassembly / Reassembly 

Air Valve / Center Section Disassembly 

Tools Required: 

 

•

 

3/16" Hex-Head Wrench 

•

 

Snap-Ring Pliers 

•

 

O-Ring Pick 

•

 

9/16" Wrench  

CAUTION: 

Before any maintenance or repair is attempted, the compressed air line to the pump should 

be disconnected and all air pressure allowed to bleed from the pump. Disconnect all intake, discharge 

and air lines. Drain the pump by turning it upside down and allowing any fluid to flow into a suitable 

container. Be aware of hazardous effects of contact with your process fluid. 

NOTE: 

Replace worn parts with genuine Wilden parts for reliable performance. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 

 

Step 1

 

Using a 9/16" wrench, loosen the bolts 

that connect the center section to the 

stand.  

CAUTION: 

With bolts removed, 

the center section is no longer 

attached to the stand and must 

be supported so that it does not 

fall from the stand.

 

Step 2

 

Remove the center section from the 

stand.

 

Step 3

 

Using a 3/16” hex wrench, loosen air valve 

bolts.

 

 

 

.

 

 

.

 

Summary of Contents for PSG WILDEN SANIFLO PS2 Series





































Reviews:

No comments

Brands by name

Popular brands

Load more brands