manualshive.com logo in svg

Dover PSG WILDEN SANIFLO PS2 Series, Engineering, Operation & Maintenance

Share
Download
Dover PSG WILDEN SANIFLO PS2 Series Engineering, Operation & Maintenance Download Page 18

 

WIL-12330-E-08

 

Wilden

® 

18 

Swivel Pump Stand Option  

 

For ease of maintenance and cleaning, Wilden offers an optional swivel pump stand. The swivel pump stand allows the 

pump to be drained by rotating the pump so that the fluid can flow out of the discharge and into a suitable container

 

 

 

Draining Pump Contents 

To drain the pump of its contents, first disconnect the inlet and discharge 

connections. Next loosen the anti-rotation bolt (item #1) by turning counter-

clockwise. Do not remove the bolt; only loosen the bolt two turns. After 

loosening the anti- rotation bolt, rotate pump 180°. This will allow the 

contents within the pump to flow out of the discharge and into a suitable 

container. After draining the pump, rotate the pump 

back to the upright position and tighten the anti-rotation bolt. 

 

Removing Pump From Swivel Pump Stand  

Saniflo™ HS pumps are very heavy. It is recommended that the pump be 

disassembled while attached to the stand. If it is necessary to remove the 

pump from the stand while fully assembled, use a hoist or mechanical 

means to support the pump as it is removed from the stand. 

To remove your Saniflo™ HS pump from the swivel pump stand, first 

loosen the anti-rotation bolt (item #1) by turning counter-clockwise. Next, 

ensure the entire pump weight is supported by hoist and loosen the locking 

pin (item #2) by turning counter-clockwise. This will allow the pump to be 

removed from the stand. 

CAUTION: 

Removal of the locking pin (item #2) will allow the 

pump to fall from the stand, potentially causing injury to the 

operator or personnel in the immediate area. Never operate or 

store the pump without the locking pin (item #2) in place and 

properly torqued. 

NOTE: 

The center 

block-to-bushing bolts 

(item #4) attach the 

center block 

mounting bushing 

(item #3) to the center 

block (not shown). 

These bolts do not 

need to be removed 

to remove the pump 

from the stand. 

NOTE: 

Torque values 

are located in Section 

7 of this manual. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Swivel Pump Stand

 

Summary of Contents for PSG WILDEN SANIFLO PS2 Series





































Reviews:

No comments

Brands by name

Popular brands

Load more brands