manualshive.com logo in svg

Dover OPW Fluid Transfer civacon 8800E, Operation Manual, Page: 13 / 35

Share
Download
Dover OPW Fluid Transfer civacon 8800E Operation Manual Download Page 13

 

Rack Monitor 8800E/8801E 
Document: Operation  Manual  
Date: 16-Jun-2011

 

Version: A.6

 

 

 

Page 13 of 35 H71343 

 

LED (electronic light indicator) Display info at power up. 

 

LED Test sequence. 
During power up the Red Error indicator in the middle small bar will start flashing every ½ second to indicate no 
communication is present. 
When the main processor starts sending messages to the LED and LC-Display board the two Blue indicators will 
start flashing inversely and the Red indicator will be switched off. 
 

1.   Middle Red  

Communication error indicator 

2.   Two Blue    

Communication indicator (flashing) 

 
The LED test sequence will continue with: 
 

3.   Left White   

Grounding indicator 

4.   Right White  

Grounding indicator 

5.   Middle Red  

Grounding error indicator 

6.   Left Yellow  

Bypass indicator 

7.   Right Yellow  

Bypass indicator 

8.   Middle Red  

System error indicator 

9.   Red bar 

 

Compartment 1 till 12 indicators 

10.   Green bar   

Compartment 1 till 12 indicators 

 
All indicators have been switched on and off and the LED display is ready to receive sensor data from the main 
controller. 
 
When no truck is connected all Red compartment indicators shall be on and a message will appear on the LC-
Display. The two blue communication indicators will flash inversely to indicate proper internal communication. 
As soon as the plug is connected to a truck an extensive short and open circuitry test will be preformed and valid 
ground verification will be shown by two inversely flashing white indicators ( see 

Figure 1

  ).  

After the auto switching mechanism has detected type and amount of sensors the indication of the Red and Green 
LED indicator compartment bar will lit up accordingly. 
 

Summary of Contents for OPW Fluid Transfer civacon 8800E




































Reviews:

No comments