manualshive.com logo in svg

Dorner 74MWWLLLSSCBBSS, Installation, Maintenance, And Parts Manual

Share
Download
Dorner 74MWWLLLSSCBBSS Installation, Maintenance, And Parts Manual Download Page 39

851-592 Rev. A

39

Dorner Mfg. Corp.

7400 Series End Drive Conveyors

Service Parts

Flat Belt

Cleated Belt

Ordering a Replacement Chain

Determine the length of chain required for the conveyor and 

round up to the nearest foot length. Order the proper number 

of chain repair kits (1' long each) for your conveyor. Dorner 

will ship chain kits that are of a reasonable length fully 

assembled.

Example:

Overall chain length = 42' 5" (rounded up = 43')
Order: Qty (43) of 74BB-WW

Belt Removal Tool

Item

Part Number

Description

 1

74BB-WW

Flat Belt Chain Repair Kit (Includes 
1 ft (305 mm) of flat belt chain and 
assembly pins)

BB = Chain Reference Number

WW = Conveyor width ref: 06 - 60 in 02 increments

Flat Belt Chain Kit

Item

Part Number

Description

 

1

74BB-WW-SS Cleated Belt Chain Repair Kit 

(Includes 1 cleat centered on a cleat 
spacing length of chain and 
assembly pins)

BB = Chain Reference Number

WW = Conveyor width ref: 06 - 60 in 02 increments

SS = Cleat Spacing

Cleated Belt Chain Kit

Item

Part Number

Description

 1

500582

Tool Rod Removal for 1" Pitch Flush 
Grid Belt

500494

Tool Rod Removal for 1/2" Pitch 
Flush Grid Belt

Summary of Contents for 74MWWLLLSSCBBSS











































Reviews:

No comments

Brands by name

Popular brands

Load more brands