manualshive.com logo in svg

Dorner 74MWWLLLSSCBBSS, Installation, Maintenance, And Parts Manual

Share
Download
Dorner 74MWWLLLSSCBBSS Installation, Maintenance, And Parts Manual Download Page 3

851-592 Rev. A

3

Dorner Mfg. Corp.

7400 Series End Drive Conveyors

Warnings – General Safety

A

 DANGER

SEVERE HAZARD!

KEEP OFF CONVEYORS. Climbing, sitting, 
walking or riding on conveyor will result in 
death or serious injury.

A

 DANGER

EXPLOSION HAZARD!

• DO NOT OPERATE CONVEYORS IN AN 

EXPLOSIVE ENVIRONMENT. The electric 
gearmotor generates heat and could ignite 
combustible vapors.

• Failure to comply will result in death or 

serious injury.

A

 WARNING

CRUSH HAZARD!

• DO NOT place hands or fingers inside the 

conveyor while it is running.

• DO NOT wear loose garments while 

operating the conveyor. Loose garments 
can become caught up in the conveyor.

• Failure to comply could result in serious 

injury.

A

 WARNING

CRUSH HAZARD!

• SUPPORT CONVEYOR SECTIONS PRIOR 

TO LOOSENING STAND HEIGHT OR 
ANGLE ADJUSTMENT SCREWS.

• Loosening stand height or angle 

adjustment screws may cause conveyor 
sections to drop down, causing serious 
injury.

A

 WARNING

SEVERE HAZARD!

LOCK OUT POWER before removing guards 
or performing maintenance. Exposed moving 
parts can cause serious injury.

A

 WARNING

BURN HAZARD!

DO NOT TOUCH the motor while operating, or 
shortly after being turned off. Motors may be 
HOT and can cause serious burn injuries.

A

 WARNING

PUNCTURE HAZARD!

Handle drive shaft keyway with care. It may 
be sharp and could puncture the skin, 
causing serious injury. 

A

 WARNING

SEVERE HAZARD!

• Dorner cannot control the physical 

installation and application of conveyors. 
Taking protective measures is the 
responsibility of the user.

• When conveyors are used in conjunction 

with other equipment or as part of a 
multiple conveyor system, CHECK FOR 
POTENTIAL PINCH POINTS and other 
mechanical hazards before system start-
up.

• Failure to comply could result in serious 

injury.

Summary of Contents for 74MWWLLLSSCBBSS











































Reviews:

No comments

Brands by name

Popular brands

Load more brands