manualshive.com logo in svg

Dorner 39M Series, Installation, Maintenance & Parts Manual

Share
Download
Dorner 39M Series Installation, Maintenance & Parts Manual Download Page 14

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual

851-558 Rev. B

14

Dorner Mfg. Corp.

   

Item 3: Leg Table (With Foot)

Leg Height Range

Leg Part Number

15”–19” (381mm–483mm)

710211–01263

16”–20” (406mm–508mm)

710211–01363

17”–21” (432mm–533mm)

710211–01463

18”–22” (457mm–559mm)

710211–01563

19”–23“ (483mm–584mm)

710211–01663

20”–24” (508mm–610mm)

710211–01763

21”–25” (533mm–635mm)

710211–01863

22”–26” (559mm–660mm)

710211–01963

23”–27” (584mm–686mm)

710211–02063

24”–28” (610mm–711mm)

710211–02163

25”–29” (635mm–737mm)

710211–02263

26”–30” (660mm–762mm)

710211–02363

27”–31” (686mm–787mm)

710211–02463

28”–32” (711mm–813mm)

710211–02563

29”–33” (737mm–838mm)

710211–02663

30”–34“ (762mm–864mm)

710211–02763

31”–35” (787mm–889mm)

710211–02863

32”–36” (813mm–914mm)

710211–02963

33”–37” (838mm–940mm)

710211–03063

34”–38” (864mm–965mm)

710211–03163

35”–39” (889mm–991mm)

710211–03263

36”–40” (914mm–1016mm)

710211–03363

37”–41” (940mm–1041mm)

710211–03463

38”–42” (965mm–1067mm)

710211–03563

39”–43” (991mm–1092mm)

710211–03663

40”–44” (1016mm–1118mm)

710211–03763

41”–45“ (1041mm–1143mm)

710211–03863

42”–46” (1067mm–1168mm)

710211–03963

43”–47” (1092mm–1194mm)

710211–04063

44”–48” (1118mm–1219mm)

710211–04163

45”–49” (1143mm–1245mm)

710211–04263

46”–50” (1168mm–1270mm)

710211–04363

47”–51” (1194mm–1295mm)

710211–04463

48”–52” (1219mm–1321mm)

710211–04563

49”–53” (1245mm–1346mm)

710211–04663

50”–54” (1270mm–1372mm)

710211–04763

51”–55” (1295mm–1397mm)

710211–04863

52”–56“ (1321mm–1422mm)

710211–04963

53”–57” (1346mm–1448mm)

710211–05063

54”–58” (1372mm–1473mm)

710211–05163

Leg Height Range

Leg Part Number

55”–59” (1397mm–1499mm)

710211–05263

56”–60” (1422mm–1524mm)

710211–05363

57”–61” (1448mm–1549mm)

710211–05463

58”–62” (1473mm–1575mm)

710211–05563

59”–63” (1499mm–1600mm)

710211–05663

60”–64” (1524mm–1626mm)

710211–05763

61”–65” (1549mm–1651mm)

710211–05863

62”–66” (1575mm–1676mm)

710211–05963

63”–67” (1600mm–1702mm)

710211–06063

64”–68” (1626mm–1727mm)

710211–06163

65”–69” (1651mm–1753mm)

710211–06263

66”–70” (1676mm–1778mm)

710211–06363

67”–71” (1702mm–1803mm)

710211–06463

68”–72” (1727mm–1829mm)

710211–06563

69”–73“ (1753mm–1854mm)

710211–06663

70”–74” (1778mm–1880mm)

710211–06763

71”–75” (1803mm–1905mm)

710211–06863

72”–76” (1829mm–1930mm)

710211–06963

73”–77” (1854mm–1956mm)

710211–07063

74”–78” (1880mm–1981mm)

710211–07163

75”–79” (1905mm–2007mm)

710211–07263

76”–80” (1930mm–2032mm)

710211–07363

77”–81” (1956mm–2057mm)

710211–07463

78”–82” (1981mm–2083mm)

710211–07563

79”–83” (2007mm–2108mm)

710211–07663

80”–84“ (2032mm–2134mm)

710211–07763

81”–85” (2057mm–2159mm)

710211–07863

82”–86” (2083mm–2184mm)

710211–07963

83”–87” (2108mm–2210mm)

710211–08063

84”–88” (2134mm–2235mm)

710211–08163

85”–89” (2159mm–2261mm)

710211–08263

86”–90” (2184mm–2286mm)

710211–08363

87”–91” (2210mm–2311mm)

710211–08463

88”–92” (2235mm–2337mm)

710211–08563

89”–93” (2261mm–2362mm)

710211–08663

90”–94” (2286mm–2388mm)

710211–08763

91”–95“ (2311mm–2413mm)

710211–08863

92”–96” (2337mm–2438mm)

710211–08963

93”–97” (2362mm–2464mm)

710211–09063

94”–98” (2388mm–2489mm)

710211–09163

95”–99” (2413mm–2515mm)

710211–09263

Service Parts

Summary of Contents for 39M Series























Reviews:

No comments

Brands by name

Popular brands

Load more brands