manualshive.com logo in svg

Doosan HP450WJD T3, Operation & Maintenance Manual

Share
Download
Doosan HP450WJD T3 Operation & Maintenance Manual Download Page 99

Maintenance

Operating & Maintenance Manual

Book: 23252059 (08-2010) Rev B

99

Completely drain the receiver/separator system including the piping and oil cooler by removing 
the drain plug(s) and collecting the used oil in a suitable container.

Replace the drain plug(s) ensuring that each one is secure.

NOTE: 

If the oil is drained immediately after the machine has been running,

then most of the sediment will be in suspension and will therefore drain more
readily.

CAUTION

!

Some oil mixtures are incompatible and result in the formation of
varnishes, shellacs or lacquers which may be insoluble.

NOTE: 

Always specify INGERSOLL RAND Pro-Tec

TM

 oil for use at all ambient

temperatures above -23

°

C.

Compressor Oil Filter Element

Refer to the 

SERVICE/MAINTENANCE CHART

 in this section for service intervals.

Running Gear Wheel Bearings

Wheel bearings should be packed with grease every 6 months. The type of grease used 
should conform to specification

 MIL-G-10924

.

Summary of Contents for HP450WJD T3



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands