Doosan HP450WJD T3 Operation & Maintenance Manual Download Page 104

Page: 104 / 130

Operating & Maintenance Manual

Maintenance

104

Book: 23252059 (08-2010) Rev B

Design Operating
Pressure

Ambient Temperature

Specification

100 psi to300 psi

-10

F to 125

F (-23

C to 52

Preferred:

Ingersoll Rand Pro-Tec

Alternate: ISO Viscosity Grade 46 with rust and
oxidation inhibitors, designed for air compressor
service.

350 psi

(-23

C to 52

C) -10

F to 125

Preferred:

Ingersoll Rand XHP 605

Alternate: Ingersoll Rand XHP 405

ISO Viscosity Grade 68 Group 3 or 5 with rust
and oxidation inhibitors designed for air
compressor service.

F to 125

F (-18

C to 52

Preferred:

XHP605 Ingersoll Rand XHP 1001

Ingersoll Rand
Preferred Fluids

1 gal. (3.8 Litre)

5 gal. (19.0 Litre)

55 gal. (208.2 Litre

220 gal. (836 litre)

Preferred

Ingersoll Rand Pro-Tec

36899698

36899706

36899714

36899722

Ingersoll Rand XHP605

---

22252076

22252050

22252068

Ingersoll Rand XHP 1001

---

35612738

35300516

---

XHP405

---

22252126

22252100

22252118

Engine Oil

54480918

36875938

36866903

Summary of Contents for HP450WJD T3



































































































































Search results

Summary of Contents for HP450WJD T3

Reviews:

Doosan HP450WJD T3, Operation & Maintenance Manual, Page: 104 / 130

Search results

Summary of Contents for HP450WJD T3

Reviews: