manualshive.com logo in svg

Doosan HP450WJD T3, Operation & Maintenance Manual

Share
Download
Doosan HP450WJD T3 Operation & Maintenance Manual Download Page 92

Operating & Maintenance Manual

Maintenance

92

Book: 23252059 (08-2010) Rev B

Compressor Oil Filter

Refer to the 

MAINTENANCE CHART

 in this section for the recommended servicing intervals.

Removal

WARNING

!

Do not remove the filter(s) without first making sure that the machine is
stopped and the system has been completely relieved of all air pressure.

(Refer to 

STOPPING THE UNIT

 in the 

OPERATING INSTRUCTIONS

 section

of this manual).

Clean the exterior of the filter housing and remove the spin-on element by turning it in a 
counter-clockwise direction.

Inspection

Examine the filter element.

CAUTION

!

If there is any indication of the formation of varnishes, shellacs or
lacquers on the filter element, it is a warning that the compressor
lubricating and cooling oil has deteriorated and that it should be changed
immediately. Refer to LUBRICATION later in this section.

Reassembly

Clean the filter gasket contact area and install the new element by screwing in a clockwise 
direction until the gasket makes contact with the filter housing. Tighten a further ½ to ¾ of a 
revolution.

CAUTION

!

Start the machine (refer to PRIOR TO STARTING and STARTING THE
UNIT in the OPERATING INSTRUCTIONS section of this manual) and
check for leakage before the machine is put back into service.

Summary of Contents for HP450WJD T3



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands