manualshive.com logo in svg

Doosan HP450WJD T3, Operation & Maintenance Manual

Share
Download
Doosan HP450WJD T3 Operation & Maintenance Manual Download Page 73

Lubrication

Operating & Maintenance Manual

Book: 23252059 (08-2010) Rev B

73

Symptom

Problem

Solution

Low oil pressure

Low oil level.

Add oil

Improper type of oil.

Drain, fill crankcase with oil of proper 
Viscosity and quality.

High oil consumption

Crankcase oil too light.

Use proper viscosity oil.

Oil leaks.

Check for leaks in lines, gaskets, and 
drain plug.

Restricted crankcase vent tube.

Clean vent tube.

Defective turbocharger.

See your authorized servicing dealer.

Engine emits white 
smoke

Improper type of fuel.

Use proper fuel.

Low engine temperature.

Warm up engine to normal operating 
temperature.

Defective thermostat.

Remove and check thermostat.

Defective injection nozzles.

See your authorized servicing dealer.

Engine emits black or 
gray exhaust smoke

Improper type of fuel.

Use proper fuel.

Clogged or dirty air cleaner.

Service air cleaner.

Engine overloaded.

Reduce load.

Injection nozzles dirty.

See your authorized servicing dealer.

Electronic fuel system problem

See your authorized servicing dealer.

Turbocharger not functioning.

See your authorized servicing dealer.

Summary of Contents for HP450WJD T3



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands