Doosan HP450WJD T3 Operation & Maintenance Manual Download Page 44

Page: 44 / 130

Operating & Maintenance Manual

Operating Instructions

Book: 23252059 (08-2010) Rev B

Operating Instructions

Prior to Starting

1. Place the unit in a position that is as level as possible. The design of the unit

permits a 15 degree lengthways and sideways limit on out of level operation. It
is the engine, not the compressor, that is the limiting factor.

When the unit has to be operated out of level, it is important to keep the engine
oil level near the high level mark (with the unit level).

CAUTION

Do not overfill either the engine or the compressor with oil.

2. Check the engine lubrication oil in accordance with the operating instructions

in the

Engine Operator's Manual

3. Check the compressor oil level in the sight glass located on the separator tank.

4. Check the diesel fuel level. A good rule is to top up at the end of each working

day. This prevents condensation from occurring in the tank.

Summary of Contents for HP450WJD T3



































































































































Search results

Summary of Contents for HP450WJD T3

Reviews:

Related manuals for HP450WJD T3

Brands by name

Popular brands

Doosan HP450WJD T3, Operation & Maintenance Manual

Search results

Summary of Contents for HP450WJD T3

Reviews:

Related manuals for HP450WJD T3

Brands by name

Popular brands