manualshive.com logo in svg

Doosan HP450WJD T3, Operation & Maintenance Manual

Share
Download
Doosan HP450WJD T3 Operation & Maintenance Manual Download Page 72

Operating & Maintenance Manual

Lubrication

72

Book: 23252059 (08-2010) Rev B

Symptom

Problem

Solution

Engine runs 
irregularly or stalls 
frequently

Low coolant temperature.

Remove and check thermostat.

Clogged fuel filter.

Replace fuel filter element.

Water, dirt, or air in fuel 
system.

Drain, flush, fill, and bleed system. Dirty or 
faulty injection nozzles. Have authorized 
servicing dealer check injectors.

Electronic fuel system 
problem

See your distributor or servicing dealer.

Below normal 
Engine 
temperature

Defective thermostat.

Remove and check thermostat.

Defective temperature gauge 
or sender.

Check gauge, sender, and connections.

Lack of power

Engine overloaded.

Reduce load.

Intake air restriction.

Service air cleaner.

Clogged fuel filter.

Replace filter elements.

Improper type of fuel.

Use proper fuel.

Overheated engine.

See "Engine Overheats".

Below normal engine 
temperature.

Remove and check thermostat.

Improper valve clearance.

See your authorized servicing dealer.

Dirty or faulty injection 
nozzles.

Have authorized servicing dealer check 
injectors.

Injection pump out of time.

See your authorized servicing dealer.

Electronic fuel system 
problem

See your authorized servicing dealer.

Turbocharger not functioning. 
(Turbocharger engines only)

See your authorized serving dealer.

Leaking exhaust manifold 
gasket.

See your authorized servicing dealer.

Defective aneroid control line.

See you authorized servicing dealer.

Restricted fuel hose.

Clean or replace fuel hose.

Low fast idle speed.

See your authorized servicing dealer.

Summary of Contents for HP450WJD T3



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands