manualshive.com logo in svg

Doosan B20S-3, Specifications Systems Operation Testing & Adjusting, Page: 103 / 123

Share
Download
Doosan B20S-3 Specifications Systems Operation Testing & Adjusting Download Page 103

 

102

 

MicroController Control System

Testing And Adjusting

 

Electrical System Adjustments

 

Accelerator Control Linkage

 

Method A (Mechanical)

 

(1) Rod As.  (2) Nut.  (3) Stopper.  (4)Pedal.

 

1.

 

 Disconnect the battery and discharge the head

    capacitor.

 

2.

 

 Adjust length of Rod (1) to 80 

 

±

 

 2 mm and tighten 

    the nut (2). Fully depress accelerator pedal (4) until 
    stopped by accelerator stopper (3). 

 

3.

 

 Release accelerator pedal (4). Check for 

    dimension.

 

Method B (Electrical)

1.

 

 Enter Quick diagnostics, through the specified 

    procedure, the display is an “A0”.

 

2.

 

 Depress the accelerator slowly to stop. The speed

    symbols will increase from 0 to 10 on LCD.

4

1

2

3

80

 

Parking Brake Switch

 

The lift truck can move suddenly. Injury to 
personnel or damage to the lift truck is possible.
Safely lift the drive wheels off the floor. Put blocks
of wood under the frame so both drive wheels are
free to turn. Keep away from drive wheels that
turn.

 

Parking Brake Switch Adjustment 
(1) Switch.  (2) Plate.  (3) Bolts.

 

1.

 

 Close the seat switch and turn the key to ON.

 

2.

 

 Release the parking brake and put the truck in 

    forward.

 

3.

 

 Reposition plate (2) so the switch (1) actuator is

    against the bracket. Tighten bolts (3).

 

4.

 

 Engage the parking brake and the park brake 

    symbol will be displayed. Repeat the procedure
    until adjustment is correct.

WARNING

2

3

1

Summary of Contents for B20S-3




























































































































Reviews:

No comments