manualshive.com logo in svg

DoorKing 1601 Series, Installation Manual

The DoorKing 1601 Series is a high-quality, reliable access control system for commercial spaces. Ensure a smooth installation with our comprehensive Installation Manual, available for free download from manualshive.com. This user-friendly manual provides step-by-step instructions, making the setup process effortless and hassle-free.

Share
Download
background image

120 S. Glasgow Avenue

Inglewood, California 90301 

U.S.A.

REVERSE EDGE / RED GREEN LED INSTALLATION

Installation

DoorKing Part Numbers

8080-080

Reverse Edge

8080-096

Reverse Edge + Red/Green LED

This kit is designed

 

to install on a 14 ft aluminum 

octagon arm

 for a 1601 barrier gate operator. 

It 

CANNOT

 be used with a 1602 or 1603 operators.

Note: DO NOT

 operate arm with a malfunctioning reverse edge.

Push a screwdriver through the hole in cap to release 
spring 

while

 pushing cap on. Keep pushing cap on 

until a “

CLICK

” is heard which locks it in place.

Tip:

 Liquid soap will help 

reverse edge slide on easier.

      Reinstall End Cap

Slide on Edge

3

Tip:

 Liquid soap will help 

spacer slide on easier.

Slide on Spacer

2

3

Octagon Arm

Reverse/LED Edge

Reverse/LED Edge

Spacer

Remove End Cap

Push a screwdriver through hole 
in bottom of end cap to release 
spring 

while

 pulling cap off.

1

Cover

5

” Rubber Spa

cer

Spacer MUST be
used or edge will
slide in slot.

Spacer MUST be used or 
edge will slide in slot.

Spacer

10

1601-269-G-7-21

Summary of Contents for 1601 Series












Reviews:

No comments

Related manuals for 1601 Series

Brands by name

Popular brands

Load more brands