DoorKing 1601 Series Installation Manual Download Page 3

Page: 3 / 11

Install Arm

Arm and Reverse Edge Note:

Arm has already been assembled when using 2-piece arm.
See page 9 for more information.

Reverse edge has already been installed on arm.
See page 10 for more information.

Arm sleeve snaps into release rollers.

Release
Rollers

Option #2

Arm Pivot Bolt

Break-A

way

Arm Bracket

Angled E

Optio

nal Reve

rse Edge

Arm

Sleeve

Option #1

Brea

k-A

way

Arm Bracke

Angled

End

Release
Rollers

Arm Pivot Bolt

Arm S

leeve

Optional Reverse Edge

Drawings NOT to scale

Octagon Arm

Optional Reverse/LED Edge

Spacer MUST be used or edge will slide in slot.

Optional Reverse/LED Edge

Spacer (Required)

Cover

DoorKing Part Number

1601-295

Potential

arm bending

and breaking

point if reinforcing
sleeve is not used.

Potential

arm bending

and breaking

point if reinforcing
sleeve is not used.

1601-269-G-7-21

Summary of Contents for 1601 Series












Search results

Summary of Contents for 1601 Series

Reviews:

Related manuals for 1601 Series

Brands by name

Popular brands

DoorKing 1601 Series, Installation Manual

Search results

Summary of Contents for 1601 Series

Reviews:

Related manuals for 1601 Series

Brands by name

Popular brands