Dodge 2007 RS Caravan Owner'S Manual Download Page 408 | Manualshive

Page: 408 / 520

background image

WARNING!

Fast spinning tires can be dangerous. Forces gener-
ated by excessive wheel speeds may cause tire dam-
age or failure. A tire could explode and injure
someone. Do not spin your vehicle’s wheels faster
than 35 mph (55 km/h) when you are stuck. And
don’t let anyone near a spinning wheel, no matter
what the speed.

CAUTION!

Racing the engine or spinning the wheels too fast
may lead to transmission overheating and failure. It
can also damage the tires. Do not spin the wheels
above 35 mph (55 km/h).

TOWING A DISABLED VEHICLE

With Ignition Key

Your vehicle may be towed under the following condi-
tions: The gear selector must be in NEUTRAL, the
distance to be traveled must not exceed 100 miles (160
km), and the towing speed must not exceed 44 mph (72
km/h). Exceeding these towing limits may cause a trans-
mission geartrain failure. If the transmission is not op-
erative, or if the vehicle is to be towed more than 100
miles (160 km), the vehicle must be towed with the front
wheels off the ground.

408

WHAT TO DO IN EMERGENCIES

«
...
406
407
408
409
410
...
»

Summary of Contents for 2007 RS Caravan









































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 RS Caravan

Brand: kaarta Pages: 29

HOIST-A-TOP JL CRANK

Brand: Lange Originals Pages: 13

Camaro 12000 1968 Series

Brand: Chevrolet Pages: 455

Brand: Alfa Romeo Pages: 8

Brand: THIEYE Pages: 88

Brand: Jeep Pages: 374

Brand: iSimple Pages: 16

Brand: Whispbar Pages: 43

Brand: Mont Blanc Pages: 10

Brand: Valeo Pages: 48

Brand: Mercedes-Benz Pages: 356

Brand: Emerson Pages: 24

Brand: Emerson Pages: 32

Brand: Renault Pages: 246

2005 HIGHLANDER

Brand: Toyota Pages: 423

Brand: AA Products Pages: 6

Brand: Toyota Pages: 17

Brand: Toyota Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands