Dodge 2007 RS Caravan Owner'S Manual Download Page 156 | Manualshive

Page: 156 / 520

background image

Headlight Low/High Beam Selector Switch

Pull the multifunction lever toward the steering wheel to
switch the headlights between HIGH and LOW beam.

Passing Light

You can signal another vehicle with your headlights by
lightly pulling the multifunction lever toward the steer-
ing wheel. This will cause the headlights to turn on at
high beam and remain on until the lever is released.

Windshield Wipers and Washers

The wipers and washers are operated by a switch in the
multifunction lever. Rotate the end of the lever to select
the desired wiper speed.

NOTE:

Always remove any build-up of snow that

prevents the windshield wiper blades from returning to
the OFF position. If the windshield wiper switch is
turned OFF and the blades cannot return to the OFF
position, damage to the wiper motor may occur.

To use the washer, press the end of the multifunction
lever in when spray is desired, the washers will spray for
a maximum of 20 seconds or until the lever is released. If
another washer cycle is desired the end of the lever must
be pressed again to get another 20 second washer cycle. If
the lever is depressed while in the delay range, the

Windshield Wiper/Washer Control

156

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
154
155
156
157
158
...
»

Summary of Contents for 2007 RS Caravan









































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 RS Caravan

Brand: Parrot Pages: 19

Brand: Parrot Pages: 88

Brand: Parrot Pages: 2

Brand: Parrot Pages: 2

CK 3000 Evolution

Brand: Parrot Pages: 8

CK 3000 Evolution

Brand: Parrot Pages: 106

QuadraTop Adventure Top S

Brand: Quadratec Pages: 20

Brand: Roav Pages: 10

Brand: CITROEN Pages: 52

10-8002-C11670C

Brand: Saleen Pages: 17

Truck Diesel Supplement 2012

Brand: RAM Pages: 174

Brand: Westfalia Pages: 10

51 47 0 027 792

Brand: BMW Pages: 7

Brand: Ford Pages: 728

Brand: Westin Pages: 5

PRIME DESIGN HXR-269-E-UM3-80

Brand: Safe Fleet Pages: 12

Brand: Rugged Ridge Pages: 2

Brand: Mazda Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands