Dodge 2007 RS Caravan Owner'S Manual Download Page 191 | Manualshive

Page: 191 / 520

background image

Pull up on the storage bin latch to open the cover. Slide
the storage bin locking mechanism to the

⬙

Unlocked

⬙

position to allow greater access to the storage bin.

CAUTION!

NOTE: The storage bin cover must be locked and flat
to avoid damage from contact with the front seat
tracks, which have minimal clearance to the cover.

WARNING!

In an accident, serious injury could result if the seat
storage bin covers are not properly latched. Do not
drive the vehicle with the storage bin cover open.
Keep the storage bin cover closed and latched while
the vehicle is in motion. Do not operate the storage
bin cover while the vehicle is in motion.

Overhead Rail System — If Equipped

The overhead rail system contains provisions for three
movable and removable overhead storage bins. The
storage bins may be placed anywhere on the overhead
rail system.

CAUTION!

Do not load objects over 1.5 lbs (0.68 kg) in the
storage bins. Failure to follow this could cause
damage to the Overhead Rail System.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

191

3

«
...
189
190
191
192
193
...
»

Summary of Contents for 2007 RS Caravan









































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 RS Caravan

Brand: Calira Pages: 14

For 1985-1992 GM Cars and Trucks 17933

Brand: Edelbrock Pages: 4

Brand: Masterack Pages: 4

Brand: Over Armour Offroad Pages: 5

LeisureWize EMOVE EM303A

Brand: Streetwize Pages: 20

Brand: V8 equipment Pages: 17

Car Cup Holder Phone Mount

Brand: UGREEN Pages: 9

Code Alarm PROFESSIONAL SERIES CA 5550SST

Brand: Audiovox Pages: 14

Brand: Volvo Pages: 42

Brand: Unex Pages: 30

Brand: Discount Car Stereo Pages: 8

Brand: Mercedes-Benz Pages: 398

XC70 - ANNEXE 808

Brand: Volvo Pages: 8

Brand: ULTIMATE SPEED Pages: 26

Brand: Yakima Pages: 12

Brand: Mercedes-Benz Pages: 434

Brand: ACV Pages: 2

Brand: Mitsubishi Pages: 300

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands