Dodge 2007 RS Caravan Owner'S Manual Download Page 51 | Manualshive

Page: 51 / 520

background image

4. Position the lap belt across your thighs, below your
abdomen. To remove slack in the lap belt portion, pull up
on the shoulder belt. To loosen the lap belt if it is too tight,
tilt the latch plate and pull on the lap belt. A snug belt
reduces the risk of sliding under the belt in a collision.

WARNING!

•

A lap belt worn too high can increase the risk of

internal injury in a collision. The belt forces won’t
be at the strong hip and pelvic bones, but across your
abdomen. Always wear the lap belt as low as pos-
sible and keep it snug.

•

A twisted belt can’t do its job as well. In a collision

it could even cut into you. Be sure the belt is straight.
If you can’t straighten a belt in your vehicle, take it
to your dealer and have it fixed.

5. Position the shoulder belt on your chest so that it is
comfortable and not resting on your neck. The retractor
will withdraw any slack in the belt.

Removing Slack From Belt

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

51

2

«
...
49
50
51
52
53
...
»

Summary of Contents for 2007 RS Caravan









































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 RS Caravan

Brand: iDataLink Pages: 106

Brand: Yakima Pages: 11

Brand: Zavoli Pages: 26

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

Brand: TrailFX Pages: 6

Brand: Mazdaspeed Pages: 8

For 1985-1992 GM Cars and Trucks 17933

Brand: Edelbrock Pages: 4

Brand: Prorack Pages: 14

Brand: Honda Pages: 208

Brand: Thule Pages: 8

Brand: Voxoa Pages: 48

Brand: Bestop Pages: 31

Brand: Dakota Digital Pages: 20

Brand: Mopar Pages: 17

Charger SRT 392 2017

Brand: Dodge Pages: 576

Brand: Lexus Pages: 108

transit connect 2012

Brand: Ford Pages: 299

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands