Doco DOCOMATIC 1200, Installation Manual

Page: 8 / 23

39
5sec.
1x
1x
1-9x
1x
1x
1x
1x
1-4x
1x
1x
1x
1x
1-5x
1x
1x
1x
1x
1-4x
1x
1x
1x
1x
1-5x
1x
1x
1x
1x
1x
1x
1x 1x
1x
1-7x
1x 1x
1x
1x
1x
1x
L
b
1x
1x
(...)
(...)
1x 1x
1x
1x
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
START S
START S
START S
MENUE
SCROLL
SCROLL
SCROLL
SCROLL SCROLL
SCROLL
SCROLL SCROLL
ENTER
SCROLL
SCROLL SCROLL
SCROLL
SCROLL SCROLL
SCROLL
SCROLL
SCROLL
SCROLL
SCROLL
SCROLL
SCROLL
SCROLL SCROLL
SCROLL
SCROLL
SCROLL
MENUE
MENUE
1x
1x
U
A
H
F
P
ENTER
ENTER
ENTER
ENTER
TRAINING PATH AND FORCE - PLEASE NOTE!
•Training the paths can be carried using permanent or mul-
tiple individual operations (fine adjustment at the end) of the
"START" button. Reset is not possible!
•Programming the path and force must both be completed
in full.
•After programming the positions "Door open" / "Door
closed" (Indication „3"), by pressing the "START" button once
again the device performs a fully automatic cycle to save
the force curve.
•Power-operated shutdown and safety devices connected
are inactive during the programming phase – in the event of
an overload (e.g. pressing "START" with the door stop in the
end position), fuse F2 will blow!
MENU - PLEASE NOTE!
•The menu must be activated by pressing the "MENUE" button
for about 5 sec. The first thing to appear in the display is "P".
•With the help of the "SCROLL" buttons you can select the indi-
vidual menus "P" to "E".
•You can enter the respective menu displayed by pressing the
"ENTER" button once.
•When you enter a submenu "F" to "L" the value set is always
displayed (the characters displayed in bold
represent the pre-programmed factory setting).
You can page through the individual values respectively using
"SCROLL". After reaching the maximum value
pressing the "SCROLL" button once again will display the mini-
mum value. You can quit the respective menu with "ENTER",
which
always saves the current value displayed.
•After completing the settings on "E" you must quit the menu by
pressing the "ENTER" button once.
•The "H" setting is only possible when the signal module has
been installed and "b 3." is inactive or disabled.
•The "A" and "U" settings are only possible when "b 3." is active
or enabled.
•The "L" setting affects both the integrated lighting and any ex-
ternal lighting connected to the terminals 15-17.
•In the "b" menu, the options restricted to 0 or 1 are grouped
respectively in separate and independent submenus. For the
sake of better orientation, please note that the submenus 1.
to 7. are always displayed here with a "." after the digit.
till the door
opens
automatic
till door is opend
Save
Save
1. REVERSING 0 = Full 1= 10cm
2. SOFT MOVEMENT 0 = 7cm 1 = 15cm
3. AUTOMATIC CLOSING 0 = disabled 1 = enabled
4. LIGHT BARRIER
0 = disabled 1 = enabled
5. LIGHT BARRIER 0 = disabled 1 = enabled
6. WARNING LAMP 0 = Flashing 1 = Continuously lit
7. FACTORY SETTING 0 = disabled 1 = Reset
CAPTIONS
User action
LED on
LED off
LED flashes
LED green
LED red
7-segment display
END (Ready for operation)
START (Ready for operation)
Programming of path and force
Shutdown
force
Signal Lead
time
Lead time for
warning lamp
Door open
time
Illumination
period
Binary add-on
functions
till the door is
closed
automatic
till door is closed
DOCO MATIC
8/23 04-10