4.8 Emergency off / flap door contact
ATTENTION! The factory-fitted wire jumper across the terminals 3/4 may not be removed under any circumstances
if the connection is not being used - this prevents the device from starting!
Potential-free NC (normally closed contacts) of any safety device or its signal transmission can be connected to the termi-
nals 3/4.
In general, triggering the connection prevents the drive from starting when it is at a standstill; triggering the connection
while opening causes the drive to stop immediately and start reversing (direction reversal after opening). After resetting the
trigger, the drive can be operated again in the regular manner.
Before connecting an element, remove the factory-fitted wire jumper. Use a cable core of at least 0.25mm² cross-section
for the connection with a maximum length up to 20 m. If a number of elements are operated at this connection, the NC
contacts must be connected in series.
4.9 Centre suspension
The centre suspension provides extra stability to the drive depending on the installation conditions, such as heavy doors or
drives having extended rails (> 3.00 m). It has not been designed to be the only means for fixing the drive.
FIG. 33: Bring the centre suspension into place
• Place the centre suspension into the desired position from above on the rail and turn it in position.
FIG. 34: Fixing the centre suspension
• Mark the bore holes, drill the bore holes required and fix the centre suspension on both sides using the dowels, screws and
washers specified.
FIG. 35: Suspend the centre suspension using slotted brackets
• Place the centre suspension into the desired position from above on the rail and turn it in position.
• Place the slotted brackets to obtain the desired projection and fix the slotted brackets using the screws, nuts and washers
specified on both sides of the centre suspension.
FIG. 36: Fix the centre suspension to the slotted brackets
• Mark the bore holes, drill the bore holes required and fix the centre suspension on both sides using the dowels, screws
and washers specified.
5.0 OPERATING THE SYSTEM
IMPORTANT SAFETY INSTRUCTIONS: ATTENTION – IT IS IMPORTANT FOR SAFEGUARDING HUMAN LIVES TO COMPLY WITH
ALL INSTRUCTIONS! THESE INSTRUCTIONS MUST BE KEPT IN SAFE CUSTODY!
When operating the emergency unlocking mechanism, there can be uncontrolled movements of the garage door
if springs are weak or broken or if the door is not balanced by weight. The emergency unlocking mechanism may
only be operated when the mains plug has been removed.
5.1 Instructions for safe operation
• Do not lean on the cord of the emergency unlocking mechanism with your body weight.
• Do not fasten any objects to the cord of the emergency unlocking mechanism or other components of the garage door
drive.
• Please ensure that the emergency unlocking mechanism or other moving parts of the system do not get caught on the
roof supporting structure or other projections of the motor vehicle or the garage door or any other objects in the garage.
• In the event of malfunctions or faults, the garage door can be opened / closed manually by operating the emergency
unlocking mechanism.
• Attention: The garage door can close faster if springs are weak, broken or defective and if the door weight is not balan-
ced properly.
• Only operate the garage door when you can see the entire area covered by the door. Please ensure that there are no
human beings or objects in the path of movement of the garage door. Observe the moving door and keep persons away
until the door has opened or closed completely and has stopped moving.
• Ensure that the garage door is completely open and has stopped moving before driving in and out of the garage.
• Do not keep the handheld transmitter in tight pant pockets or similar clothing. This can cause unintended operation.
Do not allow children to play with the drive. Keep the wireless handheld transmitter away from children.
Please do not operate the garage door system if any repair or service work needs to be done, since a fault in
the system or an incorrectly adjusted garage door can lead to severe injuries. Please ensure that such work is
only carried out by qualified and skilled technicians.
Please do not operate the garage door system if any repair or service work needs to be done, since a fault in the
system or an incorrectly adjusted garage door can lead to severe injuries. Please ensure that such work is only
carried out by qualified and skilled technicians.
DOCO
MATIC
19/23
04-10
Summary of Contents for DOCOMATIC 1200
Page 2: ...1 2 3 4 5 6 8 7 Ø3 Ø10 Ø5 6 10 13 17 a b e c d 1 2 3 4 Motor a DOCOMATIC 2 23 04 10 ...
Page 3: ...10 13 14 15 16 11 12 9 a b d c b a a b c 0 5 cm 0 5 cm DOCOMATIC 3 23 04 10 ...
Page 4: ...18 21 22 23 24 19 17 20 a Ø10 c Ø10 b 90 5 7cm max 30 DOCOMATIC 4 23 04 10 ...
Page 5: ...26 29 30 31 32 27 25 28 2x 4x a b Ø5 b 1 2 a Ø3 a b DOCOMATIC 5 23 04 10 ...
