background image

Touch Screen (Option) 

 

100 

Manual 

DLoG X Series 

14.6.

 

Resistance 

14.6.1.

 

Mechanical resistance 

Pencil hardness test ASTM D 3363-92a 

The resistive DLoG touch screens have a hardness  

 4 H. 

Test scale (from softest to hardest):  

6 B, 5 B, 4 B, 3 B, 2 B, B, HB, F, H, 2 H, 3 H, 4 H, 5 H, 6 H, 7 H, 8 H, 9 H 

 

14.6.2.

 

Chemical resistance 

The touch screen surface finish is unaffected by exposure to the following chemicals for 
a period of one hour at 22 °C, 45% relative humidity. ASTM-F-1598-95. 

Household chemicals: 

Tea, Coffee, Ketchup, Mustard, Vinegar, Beer, Coca-Cola

®

, Red Wine, Cooking Oil, 

Wisk

®

, Laundry Detergent, Fantastik

®

, All Purpose Cleaner, Joy

®

 Dishwashing Liquid, 

Windex

®

, Formula 409

®

 Cleaner, Clorox

®

, Bleach (5.25%), Hydrogen Peroxide (3%), 

Lysol, Ethyl Alcohol, Isopropyl Alcohol 

Industrial Chemicals: 

Acetone, Methyl Ethyl Ketone (MEk), Toluene, Concentrated Hydrochlorid Acis, 
Naptha, Mineral Spirits, Gasoline, 10W30 Motor Oil, Diesel Fuel, Transmission Fluid, 
Brake Fluid, Antifreeze, Hydrauic Oil 

Summary of Contents for DLoG X 10

































































































































































Reviews: