DIY-Thermocam V2 Assembly Manual Download | Manualshive

Page: 9 / 22

background image

9.

• Solder the step-up converter to the PCB by using a 3 pin strip
• Solder the four 4.7k resistors (the smaller ones) to their position on the PCB
• Solder the two 10k resistors (bigger ones) to their position right to the spot sensor
• Solder the charging module to the PCB by using a pin strip together with four

single ones

• Cut the pins short on the backside with cutting pliers
• Solder the coin cell battery holder to the PCB

DIY-Thermocam V2 Assembly Guide

Page 9

DIY-Thermocam V2 Assembly Guide

«
...
7
8
9
10
11
...
»

Summary of Contents for V2























Reviews:

No comments

Related manuals for V2

Brand: Canon Pages: 90

Brand: Canon Pages: 76

Prima Super 130 Caption

Brand: Canon Pages: 2

Brand: Canon Pages: 196

Brand: Canon Pages: 2

Brand: Lanoptik Pages: 12

Brand: Speco Pages: 13

Brand: Siqura Pages: 2

Stylus Verve - Stylus Verve 4MP Digital Camera

Brand: Olympus Pages: 192

CAMEDIA C-3020 Zoom

Brand: Olympus Pages: 180

Brand: Alpine Pages: 4

Brand: Gator Pages: 18

Brand: StarLogic Pages: 21

Brand: Ihagee Pages: 44

Brand: Papago Pages: 17

Brand: Walimex Pro Pages: 32

V8-80HS-1 series

Brand: Vicon Pages: 14

Brand: BenQ Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands