DIY-Thermocam V2 Page 11 Assembly Manual Download | Manualshive

Page: 11 / 22

background image

11.

• Put the charging LED to the place labeled CHG-LED with the short leg in the hole

G

• You can put it all the way in, then bend the LED to the top as shown on the image

and solder it

• Solder the battery connector to the place labeled LIPO on the right side
• On the left side, solder the display connector in the 40 holes, make sure it really

sits tight

• Attach the adhesive tape for the lithium battery

DIY-Thermocam V2 Assembly Guide

Page 11

DIY-Thermocam V2 Assembly Guide

«
...
9
10
11
12
13
...
»

Summary of Contents for V2























Reviews:

No comments

Related manuals for V2

Brand: Canon Pages: 76

Prima Super 130 Caption

Brand: Canon Pages: 2

Brand: Canon Pages: 196

Brand: Canon Pages: 2

CAMEDIA C-2100 Ultra Zoom

Brand: Olympus Pages: 2

Brand: Rollei Pages: 10

Brand: Rollei Pages: 91

Brand: Olympus Pages: 4

Brand: A-MTK Pages: 17

Brand: ViewSonic Pages: 27

Brand: Xcellon Pages: 16

MX-20, MX-15, RX-20, ad RX-15

Brand: RoboSHOOT Pages: 56

Brand: Vivitar Pages: 68

Brand: VADDIO Pages: 69

Brand: Polaroid Pages: 46

Brand: Uniden Pages: 2

Brand: Recordex Pages: 2

Brand: CompuSTAR Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands