background image

AIR SUCTION

AIR EXPULSION

CONDENSATE

DRAINAGE

2a. Installation of the unit

IMPORTANT

: Handle the unit with care paying extra attention to avoid damaging or scratching the parts of the unit that will

remain in view.
Hang the air conditioner on the bracket provided on the ceiling by passing  the condensate drainage pipe correctly along the air
expulsion pipe and then checking the unit's stability.

Rear grills

electric heating element

Threaded bars 
(or chains or other
fastening systems)

Partition wall or
glass (not a bea-
ring wall)

air conditioner

Condensate drainage

Internal conden-
sate drainage
pipe

The pipe protection grills must be applied outside the wall where the unit is installed.
Cut part of the right grill (looking at the unit from the rear) in order to permit the con-
densate drainage pipe to exit correctly (see Figure).

3a. Rear grills

At the end of installation, the grills must be applied to the air circulation pipes.
As above, this particular measure will ensure better unit operation because not only will the air be filtered and therefore the heat
exchange system will remain cleaner (and maintain yield over a longer period of time), but will also prevent the deposit of leaves or
other clogging material in the hosing and infiltration by birds or other small animals.
These grills can be quickly removed and cleaned whenever necessary.

VIEW OF AIR CONDITIONER REAR GRILLS

4a. Position the air conditioner and connect it to the power supply by plugging in the plug. Before starting, make sure that the plug is
adequate to the air conditioner's power absorption and the regulations in force.

37

Air pipe

Insulated air pipe

Summary of Contents for RDW 9RN





















Reviews: