background image

5

933.TL2 4.12.193.2 2015 Toyota Sienna (Smart Key)
© 2021-02-19 Directed.  All rights reserved.

OEM remote starter detection

If the vehicle has an active OEM remote starter it will program into convenience only (no immobilizer bypass). The reason for this 

is to allow aftermarket security to be installed while keeping the factory remote starter active. If you wish for the interface to control 

the remote start sequence, perform one of the following:

If the vehicle is equipped with an Add-On Lexus/Toyota OEM remote starter

Some Lexus/Toyota vehicles may have an Add-On remote starter. If the OEM unit is installed, whether Active or Inactive, it 

MUST

 

be permanently disconnected, as both modules cannot coexist. Refer to 'Physical OEM remote start locations" in the chart below 

and always physically inspect and disconnect any OEM remote starter before programming any Directed products. 

Physical OEM remote start locations

Make

Model

OEM remote starter & connectors location

Toyota

Venza (Smart Key) 

Behind glove box.

Lexus

RX 450h (Smart Key) 

Behind glove box.

Lexus

RX 350 (Smart Key) 

Behind glove box.

Toyota

4Runner (Smart Key) 

Behind glove box & passenger kick panel.

Toyota

Sienna (Smart Key) 

Behind glove box & passenger kick panel.

Lexus

HS 250h (Smart Key) 

Behind glove box.

Prius

Prius (Smart Key) 

Under dash panel & driver kick panel.

Lexus

CT 200h

Behind glove box.

Lexus

GX 460 (Smart Key) 

Behind glove box.

Toyota

Prius V (Smart Key) 

Behind glove box.

If the vehicle is equipped with a BCM Enabled Lexus/Toyota OEM remote starter:

 

The vehicle does not have a physical remote starter and only one module can be programed at a time. In this case temporarily 

disable the OEM remote start system using the following process:

1. 

Remove

 the fuse powering the OEM Remote Starter. See "OEM remote start fuse location" 

2. Perform a "Soft reset" or "Hard reset".

3. Perform the "Module programming".

4. After programming is successful, 

re-insert

 the fuse powering the OEM Remote Starter.

OEM remote start fuse location

Make

Model

Fuse Location

Fuse Name Fuse 

Value

Lexus

CT 200h (Smart Key)

Engine room relay box, left side of engine compartment.

MAYDAY

10A

Lexus

GX 460 (Smart Key)

Engine room relay box, left side of engine compartment.

MAYDAY

7.5A

Lexus

RX 350 (Smart Key)

Engine room relay box, left side of engine compartment.

MAYDAY/TEL

7.5A

Lexus

RX 450h (Smart Key)

Engine room relay box, left side of engine compartment.

MAYDAY

7.5A

Summary of Contents for DS3+
























Reviews: