background image

4

933.TL2 4.12.193.2 2015 Toyota Sienna (Smart Key)
© 2021-02-19 Directed.  All rights reserved.

Pre-installation and application warnings

Firmware notes:

 This section highlights important information for this specific firmware and will assist in 

pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.

T-Harness 

compatible 

THTON6

Keys required for 

programming

1

Keys required for 

operation

0

 

Š

Warning!

 No takeover feature is available on Push-to-Start vehicles.

 

Š

The keyless and Smart Key will remain functional during remote start.

 

Š

All Hybrid vehicles: for best results, set Engine Checking to OFF when flashing.

 

Š

If the vehicle is already equipped with an OEM remote starter, the installer must disconnect it before installing the DS4 plus 
module, otherwise it will not program.

 

Š

The optional Plug & Play 

THTON6

 T-Harness is sold separately.

 

Š

Important! 

All T-Harness wires 

NOT

 listed in the diagram are 

NOT 

required for the installation. Loose wires such as Siren 

Output and Hood Input may need to be pulled from the tapped section of the T-Harness. Refer to the “Wiring diagram with 
T-Harness” for more information on connections and installation instructions.

 

Š

All T-Harness wires 

NOT

 listed in the diagram are 

NOT

 required for the installation.

 

Š

Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic 
connector.

 

Š

It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each 
wiring diagram.

 

Š

Refer to the "Vehicle connections" following the installation diagram.

General notes:

 This section highlights important information for this specific firmware.

[1] 

The installation of an aftermarket hood pin is 

ONLY 

required on vehicles that are 

NOT

 equipped with a factory hood pin.

[2] 

The siren is 

ONLY 

required when enabling the security features during module flashing.

[3] 

Connection required 

ONLY 

if Pit-Stop/Idle mode is desired.

[4] 

For Security Only Installations, refer to 'Locating components in the vehicle' for the optional starter disable connection.

Summary of Contents for DS3+
























Reviews: