manualshive.com logo in svg

Dingsheng Tiangong PY180H, Operating Manual

Share
Download
Dingsheng Tiangong PY180H Operating Manual Download Page 75

71 

 

2.2 Too low shifting 
pressure in all 
gears(See pressure 
gauge) 

Oil level too low. 
 
Faults in operating pump 
 
Faults in gear shifting pressure. 

Fill up to the specified pressure. 
Notify the Sales & Service Dept. 
of our company. 
Notify the Sales & Service Dept. 
of our company. 

2.3 Too low shifting 
pressure in some 
gear 

Sealing parts, piston ring, gear 
clutch worn or broken. 

Notify the Sales & Service Dept. 
of our company. 

2.4. Too high oil 
temperature (See 
the thermometer on 
instrument panel.) 

Too low oil level. 
 
Dirty radiating fins of oil cooler. 
High or low gear used for too 
long a time. 
 
Faults in safety valve of torque 
converter. 

Fill up to the “Maximum oil 
level”. 
Clean radiating fins of oil cooler.
Change methods of driving, i.e. 
selecting a different gear to 
drive. 
Notify the Sales & Service Dept. 
of our company. 

3. Brake breakdown  Air in brake system 

Oil leakage in joints of braking 
pipes. 

Bleeding air in brake system. 
Tighten joints or replace sealing 
piece. 

4

 

Hydraulic 

steering 
4.1 Hydraulic 
steering gear or 
steering pump 
damaged. 
 

 

Notify the Sales & Service Dept. 
of our company. 

4.2 Front wheel 
wobbled 

Steering cylinder or lever 
bearing worn 

Replace bearing or 
corresponding ball pivot. 

5.Working device 
5.1Working device 
understeers or fails 
to remain in the 
selected position. 

 
Too low oil level in oil tank 
Piston sealing piece in cylinder 
damaged 
Regulated pressure by safety 
valve incorrect 
Safety valve fails to keep 
required pressure 
 

 
Fill up to the specified oil level 
Change sealing piece (Notify 
Sales & Service Dept.) 
Re-regulate (Notify Sales & 
Service Dept.) 
Replace spring or valve (Notify 
Sales & Service Dept.) 

5.2 Blade wobbled 

Steering clearance too much 

Replace, file sleeve of guide 
plate 

5.3 Blade can not 
rotate 

Joints leakage of hydraulic 
motor  
Parts of hydraulic motor worn   

Replace sealing piece 
Replace hydraulic motor (Notify 
Sales & Service Dept.) 

5.4 Too less oil 
supply or too great 

Too low oil level in oil tank 
Hydraulic pump damaged 

Fill up to the specified oil level 
Change hydraulic pump (Notify 

Summary of Contents for PY180H

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands