manualshive.com logo in svg

Dingsheng Tiangong PY180H, Operating Manual

Share
Download
Dingsheng Tiangong PY180H Operating Manual Download Page 52

48 

 

 

Operating hours 

Maintenance 

After every 3000 

operating hours   

Engine: The following work shall be carried out except for 
the maintenance items to be conducted after 100h of 
operation: 
1. Clean the cooling system. 
2. Clean the engine oil cooler. 
3. Check the internal water seal of water pump and fill new 

lubricating grease.   

4. Disassemble and check the engine, starter; clean and 

maintain fill new lubricating grease. 

5. Determine whether to disassemble cylinder cover and 

repair

 

inlet valve according to the relevant conditions. 

6. Determine whether to adjust the injection pump 

according to the relevant conditions. 

7. Determine whether to check the oil supply of engine oil 

pump. 

8. Replace engine oil filter element. 
9. Check the axial clearance at main-drive pinion of rear 

axle, if the axial clearance is more than 0.05, 
readjustment must be conducted. 

 

8.5 Engine   

8.5.1 Engine air filter   

a. Air prefilter 
According to the using condition, the air prefilter shall be disassembled to 

remove dusts with compressed air or water after operating for 100

～

150 hours

，

then 

reassemble after the air prefilter becomes dried completely. 

b. Air filter   
1. When the blocked alarm indicates from green to red, conduct maintenance to 

main filter element. 

2. The filter element must be replaced after cleaning for 5 times. 
3. The main filter element and safety filter element shall be replaced at the same 

time when replacing filter. 

4. When conducting maintenance to the filter element, beat the filter element 

slightly or blow the filter element from inside to outside with compressed air, 
reassemble the main filter element after clearing dusts and reset the blocked alarm. 

5. It is strictly forbidden to clean filter element with oil or water. 
6. When conducting maintenance to the filter element, replace the main filter 

element immediately if find damage. Check the air inlet hose from filter to engine for 
damage. Take notice of replacing damaged parts. 
 

8.5.2 Fuel system 

Note: 

When the system is operating, do not contact fuel with open fire and no 

Summary of Contents for PY180H

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands