manualshive.com logo in svg

Dingsheng Tiangong PY180H, Operating Manual

Share
Download
Dingsheng Tiangong PY180H Operating Manual Download Page 56

52 

 

  Cleaning the brake is the key for maintaining. 

     Inspect the rubber pad for aging phenomenon, replace if necessary. 
 
       

 Shoe type brake

 

     Brake system 
         

Note:

 Only professional staff can conduct repairs and maintenance. 

Check the thickness of brake lining in accordance with maintenance system 

(8.4); replace brake lining when the remained thickness is less than 3 mm. 

 

     Replace  brake  lining:  Only  professional staff can conduct repairs and 
maintenance and inspection of the brake lining. 
          The replaced brake lining must be run-in and rounded off with brake drum to 
insure necessary contact area; additionally, in order to avoid unbalanced braking force, 
the brake lining shall be replaced together with that of opposite wheel.   
     Adjust foot brake: 
 

 

 

Fig. 55 

 

Note:

 When replacing the brake with brake lining, all four wheel of the tandem 

box shall be adjusted.   

Both brake shoes of one brake shall be adjusted together; the adjusting 

sequence makes no difference. 

The adjustment shall be conducted by two people, one shall rotate the wheel 

and meanwhile the other shall adjust the brake.   

1. Raise one side of grader wheel with blade against the ground till the wheels 

apart from ground. 

2. Support the tandem box, release the hand brake. 

 

Summary of Contents for PY180H

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands