manualshive.com logo in svg

Dingsheng Tiangong PY180H, Operating Manual

Share
Download
Dingsheng Tiangong PY180H Operating Manual Download Page 73

69 

 

broken. 
    b. Needle valve and valve seat 
faces are damaged. 
    c. Needle valve is clipped. 
    d. Pressure map is deformed. 
    e. Joint face of fuel injector is 
uneven.  
5. Bad atomization 
    a. Needle valve is deformed or 
worn. 
    b. Needle valve and valve seat 
face are worn or burn out. 
    c. Nozzle opening is blocked. 
    d. Needle valve is clipped. 

 
Clean or replace parts. 
 
Replace parts. 
Polish or replace parts. 
Replace parts. 
 
 
Replace parts. 
 
Clean. 
Repair or replace. 

1.12 Fault in speed 
regulator  

1. Unstable speed regulation 
  a. Oil supply of different 
cylinder is irregular.   
    b. Nozzle hole of fuel injector 
is blocked or leaks oil. 
     

c. Plunger spring of oil pump 

and delivery valve spring are 
broken. 
2. Can not reach idle speed 
    a. Operating arm has not been 
put to bottom. 

b. Tooth ring and adjusting 

toothed bar have been clipped. 
3. Idle car 
    a. Camber of adjusting spring 
because of long use. 
  b.  Extending  and  retracting 
distances of flyball are 
inconsistent. 
 

 

c. Wearing clearance of 

floating lever.   
4. Propeller racing 
    a. Rotating speed is too high. 
  b. Speed regulating spring is 
broken. 
  c. Adjusting toothed bar and 
tooth ring are clipped. 

 
Adjust oil supply. 
 
Check or replace oil nozzle 
coupled parts assembly. 
 
Replace spring. 
 
 
 
Check and adjust. 
 
Check and process. 
 
 
Replace spring. 
 
Check and correct. 
 
 
Check and repair. 
 
 
Check and readjust. 
Replace spring. 
 
Check and repair. 
 

1.13 Diesel engine 
stops suddenly 

1. Crank shaft can not turn after 
stopping.  

 
 

Summary of Contents for PY180H

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands